Revert "config: Create printer-bq-hephestos-2014.cfg (#5607)"
This reverts commit 18119858c6.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
Kevin O'Connor
parent
18119858c6
commit
a709ba43af
|
|
@ -1,99 +0,0 @@
|
||||||
# This file contains pin mappings for the BQ Prusa i3 Hephestos from 2014
|
|
||||||
# (https://www.reprap.org/wiki/Prusa_i3_Hephestos)
|
|
||||||
# It was sold in kit form, and uses a RAMPS board with HD44780 display without
|
|
||||||
# heated bed or any modern amenities.
|
|
||||||
|
|
||||||
# To use this config, the firmware should be compiled for the AVR atmega2560.
|
|
||||||
|
|
||||||
# See docs/Config_Reference.md for a description of parameters.
|
|
||||||
|
|
||||||
[display]
|
|
||||||
lcd_type: hd44780
|
|
||||||
rs_pin: PH1
|
|
||||||
e_pin: PH0
|
|
||||||
d4_pin: PA1
|
|
||||||
d5_pin: PA3
|
|
||||||
d6_pin: PA5
|
|
||||||
d7_pin: PA7
|
|
||||||
encoder_pins: ^PC6, ^PC4
|
|
||||||
click_pin: ^!PC2
|
|
||||||
kill_pin: ^!PG0
|
|
||||||
|
|
||||||
[stepper_x]
|
|
||||||
step_pin: PF0
|
|
||||||
dir_pin: !PF1
|
|
||||||
enable_pin: !PD7
|
|
||||||
microsteps: 16
|
|
||||||
rotation_distance: 40
|
|
||||||
endstop_pin: ^!PE5
|
|
||||||
position_endstop: 0
|
|
||||||
position_max: 200
|
|
||||||
homing_speed: 50
|
|
||||||
|
|
||||||
[stepper_y]
|
|
||||||
step_pin: PF6
|
|
||||||
dir_pin: PF7
|
|
||||||
enable_pin: !PF2
|
|
||||||
microsteps: 16
|
|
||||||
rotation_distance: 40
|
|
||||||
endstop_pin: ^!PJ1
|
|
||||||
position_endstop: 0
|
|
||||||
position_max: 200
|
|
||||||
homing_speed: 50
|
|
||||||
|
|
||||||
[stepper_z]
|
|
||||||
step_pin: PL3
|
|
||||||
dir_pin: !PL1
|
|
||||||
enable_pin: !PK0
|
|
||||||
microsteps: 16
|
|
||||||
rotation_distance: 0.8
|
|
||||||
endstop_pin: ^!PD3
|
|
||||||
position_endstop: 0
|
|
||||||
position_max: 200
|
|
||||||
homing_speed: 3
|
|
||||||
|
|
||||||
[extruder]
|
|
||||||
step_pin: PA4
|
|
||||||
dir_pin: PA6
|
|
||||||
enable_pin: !PA2
|
|
||||||
microsteps: 16
|
|
||||||
# measured extruding 100mm of filament with stock Hephestos extruder
|
|
||||||
rotation_distance: 31.825
|
|
||||||
nozzle_diameter: 0.400
|
|
||||||
filament_diameter: 1.750
|
|
||||||
heater_pin: PB4
|
|
||||||
sensor_type: EPCOS 100K B57560G104F
|
|
||||||
sensor_pin: PK5
|
|
||||||
min_temp: 0
|
|
||||||
max_temp: 250
|
|
||||||
|
|
||||||
# 5 points for manual bed leveling that still leave room for accessing the stock screws
|
|
||||||
[bed_screws]
|
|
||||||
screw1: 40, 40
|
|
||||||
screw2: 180, 40
|
|
||||||
screw3: 180, 160
|
|
||||||
screw4: 40, 160
|
|
||||||
screw5: 110, 100
|
|
||||||
|
|
||||||
[fan]
|
|
||||||
pin: PH6
|
|
||||||
|
|
||||||
[printer]
|
|
||||||
kinematics: cartesian
|
|
||||||
max_velocity: 300
|
|
||||||
max_accel: 3000
|
|
||||||
# Must limit Z velocity, since RAMPS does not have enough timer resolution
|
|
||||||
max_z_velocity: 3
|
|
||||||
max_z_accel: 100
|
|
||||||
|
|
||||||
# Common EXP1 / EXP2 (display) pins
|
|
||||||
[board_pins]
|
|
||||||
aliases:
|
|
||||||
# Common EXP1 header found on many "all-in-one" ramps clones
|
|
||||||
EXP1_1=PC0, EXP1_3=PH0, EXP1_5=PA1, EXP1_7=PA5, EXP1_9=<GND>,
|
|
||||||
EXP1_2=PC2, EXP1_4=PH1, EXP1_6=PA3, EXP1_8=PA7, EXP1_10=<5V>,
|
|
||||||
# EXP2 header
|
|
||||||
EXP2_1=PB3, EXP2_3=PC6, EXP2_5=PC4, EXP2_7=PL0, EXP2_9=<GND>,
|
|
||||||
EXP2_2=PB1, EXP2_4=PB0, EXP2_6=PB2, EXP2_8=PG0, EXP2_10=<RST>
|
|
||||||
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi"
|
|
||||||
# Note, some boards wire: EXP2_8=<RST>, EXP2_10=PG0
|
|
||||||
Loading…
Reference in New Issue