config: Split generic-bigtreetech-octopus.cfg into separate files
Use two different files for the Octopus Pro and Octopus (non-Pro). The configs are the same in practice, but the difference in version and naming can lead to confusion. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
Kevin O'Connor
parent
f7567a0db9
commit
a629b87ae0
|
|
@ -0,0 +1,289 @@
|
|||
# This file contains common pin mappings for the BigTreeTech Octopus
|
||||
# Pro v1.0 board.
|
||||
|
||||
# Important! Do not use this config with an Octopus Pro v1.1 board as
|
||||
# doing so could result in a heater being inadvertently enabled.
|
||||
|
||||
# To use this config, start by identifying the micro-controller on the
|
||||
# board - it may be an STM32F446, STM32F429, or an STM32H723. Select
|
||||
# the appropriate micro-controller in "make menuconfig" and select
|
||||
# "Enable low-level configuration options". For STM32F446 boards the
|
||||
# firmware should be compiled with a "32KiB bootloader" and a "12MHz
|
||||
# crystal" clock reference. For STM32F429 boards use a "32KiB
|
||||
# bootloader" and an "8MHz crystal". For STM32H723 boards use a
|
||||
# "128KiB bootloader" and a "25Mhz crystal".
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
# Driver0
|
||||
[stepper_x]
|
||||
step_pin: PF13
|
||||
dir_pin: PF12
|
||||
enable_pin: !PF14
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: PG6
|
||||
position_endstop: 0
|
||||
position_max: 200
|
||||
homing_speed: 50
|
||||
|
||||
# Driver1
|
||||
[stepper_y]
|
||||
step_pin: PG0
|
||||
dir_pin: PG1
|
||||
enable_pin: !PF15
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: PG9
|
||||
position_endstop: 0
|
||||
position_max: 200
|
||||
homing_speed: 50
|
||||
|
||||
# Driver2
|
||||
[stepper_z]
|
||||
step_pin: PF11
|
||||
dir_pin: PG3
|
||||
enable_pin: !PG5
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: PG10
|
||||
position_endstop: 0.5
|
||||
position_max: 200
|
||||
|
||||
# Driver3
|
||||
# The Octopus only has 4 heater outputs which leaves an extra stepper
|
||||
# This can be used for a second Z stepper, dual_carriage, extruder co-stepper,
|
||||
# or other accesory such as an MMU
|
||||
#[stepper_]
|
||||
#step_pin: PG4
|
||||
#dir_pin: PC1
|
||||
#enable_pin: PA0
|
||||
#endstop_pin: PG11
|
||||
#...
|
||||
|
||||
# Driver4
|
||||
[extruder]
|
||||
step_pin: PF9
|
||||
dir_pin: PF10
|
||||
enable_pin: !PG2
|
||||
microsteps: 16
|
||||
rotation_distance: 33.500
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PA2 # HE0
|
||||
sensor_pin: PF4 # T0
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
control: pid
|
||||
pid_Kp: 22.2
|
||||
pid_Ki: 1.08
|
||||
pid_Kd: 114
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
#[filament_switch_sensor material_0]
|
||||
#switch_pin: PG12
|
||||
|
||||
# Driver5
|
||||
#[extruder1]
|
||||
#step_pin: PC13
|
||||
#dir_pin: PF0
|
||||
#enable_pin: !PF1
|
||||
#heater_pin: PA3 # HE1
|
||||
#sensor_pin: PF5 # T1
|
||||
#...
|
||||
|
||||
#[filament_switch_sensor material_1]
|
||||
#switch_pin: PG13
|
||||
|
||||
# Driver6
|
||||
#[extruder2]
|
||||
#step_pin: PE2
|
||||
#dir_pin: PE3
|
||||
#enable_pin: !PD4
|
||||
#heater_pin: PB10 # HE2
|
||||
#sensor_pin: PF6 # T2
|
||||
#...
|
||||
|
||||
#[filament_switch_sensor material_2]
|
||||
#switch_pin: PG14
|
||||
|
||||
# Driver7
|
||||
#[extruder3]
|
||||
#step_pin: PE6
|
||||
#dir_pin: PA14
|
||||
#enable_pin: !PE0
|
||||
#heater_pin: PB11 # HE3
|
||||
#sensor_pin: PF7 # T3
|
||||
#...
|
||||
|
||||
#[filament_switch_sensor material_3]
|
||||
#switch_pin: PG15
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PA1
|
||||
sensor_pin: PF3 # TB
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
control: watermark
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PA8
|
||||
|
||||
#[heater_fan fan1]
|
||||
#pin: PE5
|
||||
|
||||
#[heater_fan fan2]
|
||||
#pin: PD12
|
||||
|
||||
#[heater_fan fan3]
|
||||
#pin: PD13
|
||||
|
||||
#[heater_fan fan4]
|
||||
#pin: PD14
|
||||
|
||||
#[controller_fan fan5]
|
||||
#pin: PD15
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
||||
# CAN bus is also available on this board
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
########################################
|
||||
# TMC2209 configuration
|
||||
########################################
|
||||
|
||||
#[tmc2209 stepper_x]
|
||||
#uart_pin: PC4
|
||||
##diag_pin: PG6
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2209 stepper_y]
|
||||
#uart_pin: PD11
|
||||
##diag_pin: PG9
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2209 stepper_z]
|
||||
#uart_pin: PC6
|
||||
##diag_pin: PG10
|
||||
#run_current: 0.650
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2209 stepper_]
|
||||
#uart_pin: PC7
|
||||
##diag_pin: PG11
|
||||
#run_current: 0.650
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2209 extruder]
|
||||
#uart_pin: PF2
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2209 extruder1]
|
||||
#uart_pin: PE4
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2209 extruder2]
|
||||
#uart_pin: PE1
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2209 extruder3]
|
||||
#uart_pin: PD3
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
########################################
|
||||
# TMC2130 configuration
|
||||
########################################
|
||||
|
||||
#[tmc2130 stepper_x]
|
||||
#cs_pin: PC4
|
||||
#spi_bus: spi1
|
||||
##diag1_pin: PG6
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 stepper_y]
|
||||
#cs_pin: PD11
|
||||
#spi_bus: spi1
|
||||
##diag1_pin: PG9
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 stepper_z]
|
||||
#cs_pin: PC6
|
||||
#spi_bus: spi1
|
||||
##diag1_pin: PG10
|
||||
#run_current: 0.650
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 stepper_]
|
||||
#cs_pin: PC7
|
||||
#spi_bus: spi1
|
||||
##diag1_pin: PG11
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 extruder]
|
||||
#cs_pin: PF2
|
||||
#spi_bus: spi1
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 extruder1]
|
||||
#cs_pin: PE4
|
||||
#spi_bus: spi1
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 extruder2]
|
||||
#cs_pin: PE1
|
||||
#spi_bus: spi1
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 extruder3]
|
||||
#cs_pin: PD3
|
||||
#spi_bus: spi1
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PE8, EXP1_2=PE7,
|
||||
EXP1_3=PE9, EXP1_4=PE10,
|
||||
EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side
|
||||
EXP1_7=PE14, EXP1_8=PE15,
|
||||
EXP1_9=<GND>, EXP1_10=<5V>,
|
||||
|
||||
# EXP2 header
|
||||
EXP2_1=PA6, EXP2_2=PA5,
|
||||
EXP2_3=PB1, EXP2_4=PA4,
|
||||
EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side
|
||||
EXP2_7=PC15, EXP2_8=<RST>,
|
||||
EXP2_9=<GND>, EXP2_10=PC5
|
||||
|
||||
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
||||
|
||||
# A [probe] section can be defined instead with a pin: setting identical
|
||||
# to the sensor_pin: for a bltouch
|
||||
#[bltouch]
|
||||
#sensor_pin: PB7
|
||||
#control_pin: PB6
|
||||
#z_offset: 0
|
||||
|
||||
#[neopixel my_neopixel]
|
||||
#pin: PB0
|
||||
|
|
@ -1,12 +1,16 @@
|
|||
# This file contains common pin mappings for the BigTreeTech Octopus
|
||||
# and Octopus Pro boards. To use this config, start by identifying the
|
||||
# micro-controller on the board - it may be an STM32F446, STM32F429,
|
||||
# or an STM32H723. Select the appropriate micro-controller in "make
|
||||
# menuconfig" and select "Enable low-level configuration options". For
|
||||
# STM32F446 boards the firmware should be compiled with a "32KiB
|
||||
# bootloader" and a "12MHz crystal" clock reference. For STM32F429
|
||||
# boards use a "32KiB bootloader" and an "8MHz crystal". For STM32H723
|
||||
# boards use a "128KiB bootloader" and a "25Mhz crystal".
|
||||
# (non-Pro) boards.
|
||||
|
||||
# Important! Do not use this config with an Octopus Pro v1.1 board as
|
||||
# doing so could result in a heater being inadvertently enabled.
|
||||
|
||||
# To use this config, start by identifying the micro-controller on the
|
||||
# board - it may be an STM32F446, or STM32F429. Select the
|
||||
# appropriate micro-controller in "make menuconfig" and select "Enable
|
||||
# low-level configuration options". For STM32F446 boards the firmware
|
||||
# should be compiled with a "32KiB bootloader" and a "12MHz crystal"
|
||||
# clock reference. For STM32F429 boards use a "32KiB bootloader" and
|
||||
# an "8MHz crystal".
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
|
|
@ -227,9 +227,13 @@ CONFIG ../../config/generic-th3d-ezboard-v2.0.cfg
|
|||
CONFIG ../../config/printer-biqu-b1-se-plus-2022.cfg
|
||||
CONFIG ../../config/printer-prusa-mini-plus-2020.cfg
|
||||
|
||||
# Printers using the stm32f429
|
||||
DICTIONARY stm32f429.dict
|
||||
CONFIG ../../config/generic-bigtreetech-octopus-v1.1.cfg
|
||||
|
||||
# Printers using the stm32f446
|
||||
DICTIONARY stm32f446.dict
|
||||
CONFIG ../../config/generic-bigtreetech-octopus.cfg
|
||||
CONFIG ../../config/generic-bigtreetech-octopus-pro-v1.0.cfg
|
||||
CONFIG ../../config/generic-fysetc-s6.cfg
|
||||
CONFIG ../../config/generic-fysetc-s6-v2.cfg
|
||||
CONFIG ../../config/generic-fysetc-spider.cfg
|
||||
|
|
|
|||
Loading…
Reference in New Issue