config: Add a simplified Duet2 Eth/Wifi example config file
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
e2d8a6f02d
commit
a34613cf86
|
@ -0,0 +1,118 @@
|
|||
# This file contains common pin mappings for Duet2 Eth/Wifi boards. To
|
||||
# use this config, the firmware should be compiled for the SAM4E8E.
|
||||
|
||||
# See the example.cfg file for a description of available parameters.
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PD6
|
||||
dir_pin: PD11
|
||||
enable_pin: !PC6, tmc2660_stepper_x:virtual_enable
|
||||
step_distance: .0125
|
||||
endstop_pin: ^PC14
|
||||
position_endstop: 0
|
||||
position_max: 250
|
||||
|
||||
[tmc2660 stepper_x]
|
||||
cs_pin: PD14
|
||||
spi_bus: usart1
|
||||
microsteps: 16
|
||||
run_current: 1.000
|
||||
sense_resistor: 0.051
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PD7
|
||||
dir_pin: !PD12
|
||||
enable_pin: !PC6, tmc2660_stepper_y:virtual_enable
|
||||
step_distance: .0125
|
||||
endstop_pin: ^PA2
|
||||
position_endstop: 0
|
||||
position_max: 210
|
||||
|
||||
[tmc2660 stepper_y]
|
||||
cs_pin: PC9
|
||||
spi_bus: usart1
|
||||
microsteps: 16
|
||||
run_current: 1.000
|
||||
sense_resistor: 0.051
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PD8
|
||||
dir_pin: PD13
|
||||
enable_pin: !PC6, tmc2660_stepper_z:virtual_enable
|
||||
step_distance: .0025
|
||||
endstop_pin: ^PD29
|
||||
#endstop_pin: PD10 # E0 endstop
|
||||
#endstop_pin: PC16 # E1 endstop
|
||||
position_endstop: 0.5
|
||||
position_max: 200
|
||||
|
||||
[tmc2660 stepper_z]
|
||||
cs_pin: PC10
|
||||
spi_bus: usart1
|
||||
microsteps: 16
|
||||
run_current: 1.000
|
||||
sense_resistor: 0.051
|
||||
|
||||
[extruder]
|
||||
step_pin: PD5
|
||||
dir_pin: PA1
|
||||
enable_pin: !PC6, tmc2660_extruder:virtual_enable
|
||||
step_distance: .002
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: !PA20
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC15
|
||||
control: pid
|
||||
pid_Kp: 22.2
|
||||
pid_Ki: 1.08
|
||||
pid_Kd: 114
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
[tmc2660 extruder]
|
||||
cs_pin: PC17
|
||||
spi_bus: usart1
|
||||
microsteps: 16
|
||||
run_current: 1.000
|
||||
sense_resistor: 0.051
|
||||
|
||||
#[extruder1]
|
||||
#step_pin: PD4
|
||||
#dir_pin: PD9
|
||||
#enable_pin: !PC6, tmc2660_extruder1:virtual_enable
|
||||
#heater_pin: !PA16
|
||||
#sensor_pin: PC12
|
||||
#...
|
||||
#[tmc2660 extruder1]
|
||||
#cs_pin: PC25
|
||||
#spi_bus: usart1
|
||||
#sense_resistor: 0.051
|
||||
#...
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: !PA19
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC13
|
||||
control: watermark
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PC23 # FAN0
|
||||
|
||||
#[heater_fan nozzle_cooling_fan]
|
||||
#pin: PC26 # FAN1
|
||||
|
||||
#[heater_fan board_cooling_fan]
|
||||
#pin: PA0 # FAN2
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
|
@ -71,6 +71,7 @@ CONFIG ../../config/generic-duet2-maestro.cfg
|
|||
|
||||
# Printers using the sam4e8e
|
||||
DICTIONARY sam4e8e.dict
|
||||
CONFIG ../../config/generic-duet2.cfg
|
||||
CONFIG ../../config/generic-duet2-duex.cfg
|
||||
|
||||
# Printers using the lpc176x
|
||||
|
|
Loading…
Reference in New Issue