config: Add a simplified Duet2 Eth/Wifi example config file
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
e2d8a6f02d
commit
a34613cf86
|
@ -0,0 +1,118 @@
|
||||||
|
# This file contains common pin mappings for Duet2 Eth/Wifi boards. To
|
||||||
|
# use this config, the firmware should be compiled for the SAM4E8E.
|
||||||
|
|
||||||
|
# See the example.cfg file for a description of available parameters.
|
||||||
|
|
||||||
|
[stepper_x]
|
||||||
|
step_pin: PD6
|
||||||
|
dir_pin: PD11
|
||||||
|
enable_pin: !PC6, tmc2660_stepper_x:virtual_enable
|
||||||
|
step_distance: .0125
|
||||||
|
endstop_pin: ^PC14
|
||||||
|
position_endstop: 0
|
||||||
|
position_max: 250
|
||||||
|
|
||||||
|
[tmc2660 stepper_x]
|
||||||
|
cs_pin: PD14
|
||||||
|
spi_bus: usart1
|
||||||
|
microsteps: 16
|
||||||
|
run_current: 1.000
|
||||||
|
sense_resistor: 0.051
|
||||||
|
|
||||||
|
[stepper_y]
|
||||||
|
step_pin: PD7
|
||||||
|
dir_pin: !PD12
|
||||||
|
enable_pin: !PC6, tmc2660_stepper_y:virtual_enable
|
||||||
|
step_distance: .0125
|
||||||
|
endstop_pin: ^PA2
|
||||||
|
position_endstop: 0
|
||||||
|
position_max: 210
|
||||||
|
|
||||||
|
[tmc2660 stepper_y]
|
||||||
|
cs_pin: PC9
|
||||||
|
spi_bus: usart1
|
||||||
|
microsteps: 16
|
||||||
|
run_current: 1.000
|
||||||
|
sense_resistor: 0.051
|
||||||
|
|
||||||
|
[stepper_z]
|
||||||
|
step_pin: PD8
|
||||||
|
dir_pin: PD13
|
||||||
|
enable_pin: !PC6, tmc2660_stepper_z:virtual_enable
|
||||||
|
step_distance: .0025
|
||||||
|
endstop_pin: ^PD29
|
||||||
|
#endstop_pin: PD10 # E0 endstop
|
||||||
|
#endstop_pin: PC16 # E1 endstop
|
||||||
|
position_endstop: 0.5
|
||||||
|
position_max: 200
|
||||||
|
|
||||||
|
[tmc2660 stepper_z]
|
||||||
|
cs_pin: PC10
|
||||||
|
spi_bus: usart1
|
||||||
|
microsteps: 16
|
||||||
|
run_current: 1.000
|
||||||
|
sense_resistor: 0.051
|
||||||
|
|
||||||
|
[extruder]
|
||||||
|
step_pin: PD5
|
||||||
|
dir_pin: PA1
|
||||||
|
enable_pin: !PC6, tmc2660_extruder:virtual_enable
|
||||||
|
step_distance: .002
|
||||||
|
nozzle_diameter: 0.400
|
||||||
|
filament_diameter: 1.750
|
||||||
|
heater_pin: !PA20
|
||||||
|
sensor_type: EPCOS 100K B57560G104F
|
||||||
|
sensor_pin: PC15
|
||||||
|
control: pid
|
||||||
|
pid_Kp: 22.2
|
||||||
|
pid_Ki: 1.08
|
||||||
|
pid_Kd: 114
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 250
|
||||||
|
|
||||||
|
[tmc2660 extruder]
|
||||||
|
cs_pin: PC17
|
||||||
|
spi_bus: usart1
|
||||||
|
microsteps: 16
|
||||||
|
run_current: 1.000
|
||||||
|
sense_resistor: 0.051
|
||||||
|
|
||||||
|
#[extruder1]
|
||||||
|
#step_pin: PD4
|
||||||
|
#dir_pin: PD9
|
||||||
|
#enable_pin: !PC6, tmc2660_extruder1:virtual_enable
|
||||||
|
#heater_pin: !PA16
|
||||||
|
#sensor_pin: PC12
|
||||||
|
#...
|
||||||
|
#[tmc2660 extruder1]
|
||||||
|
#cs_pin: PC25
|
||||||
|
#spi_bus: usart1
|
||||||
|
#sense_resistor: 0.051
|
||||||
|
#...
|
||||||
|
|
||||||
|
[heater_bed]
|
||||||
|
heater_pin: !PA19
|
||||||
|
sensor_type: EPCOS 100K B57560G104F
|
||||||
|
sensor_pin: PC13
|
||||||
|
control: watermark
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 130
|
||||||
|
|
||||||
|
[fan]
|
||||||
|
pin: PC23 # FAN0
|
||||||
|
|
||||||
|
#[heater_fan nozzle_cooling_fan]
|
||||||
|
#pin: PC26 # FAN1
|
||||||
|
|
||||||
|
#[heater_fan board_cooling_fan]
|
||||||
|
#pin: PA0 # FAN2
|
||||||
|
|
||||||
|
[mcu]
|
||||||
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
||||||
|
|
||||||
|
[printer]
|
||||||
|
kinematics: cartesian
|
||||||
|
max_velocity: 300
|
||||||
|
max_accel: 3000
|
||||||
|
max_z_velocity: 5
|
||||||
|
max_z_accel: 100
|
|
@ -71,6 +71,7 @@ CONFIG ../../config/generic-duet2-maestro.cfg
|
||||||
|
|
||||||
# Printers using the sam4e8e
|
# Printers using the sam4e8e
|
||||||
DICTIONARY sam4e8e.dict
|
DICTIONARY sam4e8e.dict
|
||||||
|
CONFIG ../../config/generic-duet2.cfg
|
||||||
CONFIG ../../config/generic-duet2-duex.cfg
|
CONFIG ../../config/generic-duet2-duex.cfg
|
||||||
|
|
||||||
# Printers using the lpc176x
|
# Printers using the lpc176x
|
||||||
|
|
Loading…
Reference in New Issue