config: Add ezboard configuration (#4337)
Signed-off-by: Clark Tomlinson <fallen013@gmail.com>
This commit is contained in:
parent
c19d1fbb59
commit
a345516840
|
@ -0,0 +1,131 @@
|
|||
# This file contains common pin mappings for the TH3D EZBoard Lite v1.2.
|
||||
# To use this config, the firmware should be compiled for the
|
||||
# LPC1769 with USB communication.
|
||||
|
||||
# The "make flash" command does not work on this board. Instead,
|
||||
# after running "make", copy the generated "out/klipper.bin" file to a
|
||||
# file named "firmware.bin" on an SD card and then restart the board
|
||||
# with that SD card.
|
||||
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_lpc1768_1BB0FF16871C4AAF0F5D7C5DC62000F5-if00
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 500
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[stepper_x]
|
||||
step_pin: P2.0
|
||||
dir_pin: P1.16
|
||||
enable_pin: !P1.17
|
||||
rotation_distance: 72
|
||||
endstop_pin: ^P1.24
|
||||
position_endstop: 0
|
||||
position_max: 350
|
||||
|
||||
[tmc2208 stepper_x]
|
||||
uart_pin: P0.5
|
||||
tx_pin: P0.4
|
||||
run_current: 0.600
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[stepper_y]
|
||||
step_pin: P2.1
|
||||
dir_pin: P1.10
|
||||
enable_pin: !P1.9
|
||||
rotation_distance: 72
|
||||
endstop_pin: ^P1.25
|
||||
position_endstop: 0
|
||||
position_max: 350
|
||||
|
||||
[tmc2208 stepper_y]
|
||||
uart_pin: P0.11
|
||||
tx_pin: P0.10
|
||||
run_current: 0.600
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[stepper_z]
|
||||
step_pin: P2.2
|
||||
dir_pin: P1.15
|
||||
enable_pin: !P1.14
|
||||
rotation_distance: 16
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
position_endstop: 0.5
|
||||
position_max: 400
|
||||
|
||||
[tmc2208 stepper_z]
|
||||
uart_pin: P0.20
|
||||
tx_pin: P0.19
|
||||
run_current: 0.700
|
||||
hold_current: 0.600
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[extruder]
|
||||
step_pin: P2.3
|
||||
dir_pin: P1.4
|
||||
enable_pin: !P1.8
|
||||
roration_distance: 13.5744
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: P2.7
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: P0.23
|
||||
control: pid
|
||||
pid_Kp: 22.2
|
||||
pid_Ki: 1.08
|
||||
pid_Kd: 114
|
||||
min_temp: 0
|
||||
max_temp: 210
|
||||
|
||||
[tmc2208 extruder]
|
||||
uart_pin: P0.21
|
||||
tx_pin: P0.22
|
||||
run_current: 0.800
|
||||
hold_current: 0.700
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: P2.5
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: P0.24
|
||||
control: pid
|
||||
# tuned for stock hardware with 50 degree Celsius target
|
||||
pid_Kp: 54.027
|
||||
pid_Ki: 0.770
|
||||
pid_Kd: 948.182
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: P2.6
|
||||
|
||||
#[safe_z_home]
|
||||
# home_xy_position: 175,175 # Change coordinates to the center of your print bed
|
||||
# speed: 50
|
||||
# z_hop: 10
|
||||
# z_hop_speed: 5
|
||||
|
||||
#[bltouch]
|
||||
#sensor_pin: P1.26
|
||||
#control_pin: P2.4
|
||||
|
||||
#[filament_switch_sensor my_sensor]
|
||||
#switch_pin: P1.27
|
||||
|
||||
######################################################################
|
||||
# 128x64 Full Graphic Creality CR10 / ENDER 3 stockdisplay
|
||||
######################################################################
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=P1.31, EXP1_3=P3.26, EXP1_5=P3.25, EXP1_7=P0.16, EXP1_9=<GND>,
|
||||
EXP1_2=P1.30, EXP1_4=<RST>, EXP1_6=P0.15, EXP1_8=P0.18, EXP1_10=<5V>
|
Loading…
Reference in New Issue