From a3455168405c2f544bba849445ee2346d8b14a35 Mon Sep 17 00:00:00 2001
From: Clark Tomlinson <fallen013@gmail.com>
Date: Tue, 8 Jun 2021 21:15:52 -0400
Subject: [PATCH] config: Add ezboard configuration (#4337)

Signed-off-by: Clark Tomlinson <fallen013@gmail.com>
---
 config/generic-th3d-ezboard-lite-v1.2.cfg | 131 ++++++++++++++++++++++
 1 file changed, 131 insertions(+)
 create mode 100644 config/generic-th3d-ezboard-lite-v1.2.cfg

diff --git a/config/generic-th3d-ezboard-lite-v1.2.cfg b/config/generic-th3d-ezboard-lite-v1.2.cfg
new file mode 100644
index 00000000..67b8b656
--- /dev/null
+++ b/config/generic-th3d-ezboard-lite-v1.2.cfg
@@ -0,0 +1,131 @@
+# This file contains common pin mappings for the TH3D EZBoard Lite v1.2.
+# To use this config, the firmware should be compiled for the
+# LPC1769 with USB communication.
+
+# The "make flash" command does not work on this board. Instead,
+# after running "make", copy the generated "out/klipper.bin" file to a
+# file named "firmware.bin" on an SD card and then restart the board
+# with that SD card.
+
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[mcu]
+serial: /dev/serial/by-id/usb-Klipper_lpc1768_1BB0FF16871C4AAF0F5D7C5DC62000F5-if00
+
+[printer]
+kinematics: cartesian
+max_velocity: 500
+max_accel: 3000
+max_z_velocity: 5
+max_z_accel: 100
+
+[stepper_x]
+step_pin: P2.0
+dir_pin: P1.16
+enable_pin: !P1.17
+rotation_distance: 72
+endstop_pin: ^P1.24
+position_endstop: 0
+position_max: 350
+
+[tmc2208 stepper_x]
+uart_pin: P0.5
+tx_pin: P0.4
+run_current: 0.600
+hold_current: 0.500
+stealthchop_threshold: 999999
+
+[stepper_y]
+step_pin: P2.1
+dir_pin: P1.10
+enable_pin: !P1.9
+rotation_distance: 72
+endstop_pin: ^P1.25
+position_endstop: 0
+position_max: 350
+
+[tmc2208 stepper_y]
+uart_pin: P0.11
+tx_pin: P0.10
+run_current: 0.600
+hold_current: 0.500
+stealthchop_threshold: 999999
+
+[stepper_z]
+step_pin: P2.2
+dir_pin: P1.15
+enable_pin: !P1.14
+rotation_distance: 16
+endstop_pin: probe:z_virtual_endstop
+position_endstop: 0.5
+position_max: 400
+
+[tmc2208 stepper_z]
+uart_pin: P0.20
+tx_pin: P0.19
+run_current: 0.700
+hold_current: 0.600
+stealthchop_threshold: 999999
+
+[extruder]
+step_pin: P2.3
+dir_pin: P1.4
+enable_pin: !P1.8
+roration_distance: 13.5744
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: P2.7
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: P0.23
+control: pid
+pid_Kp: 22.2
+pid_Ki: 1.08
+pid_Kd: 114
+min_temp: 0
+max_temp: 210
+
+[tmc2208 extruder]
+uart_pin: P0.21
+tx_pin: P0.22
+run_current: 0.800
+hold_current: 0.700
+stealthchop_threshold: 999999
+
+[heater_bed]
+heater_pin: P2.5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: P0.24
+control: pid
+# tuned for stock hardware with 50 degree Celsius target
+pid_Kp: 54.027
+pid_Ki: 0.770
+pid_Kd: 948.182
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: P2.6
+
+#[safe_z_home]
+# home_xy_position: 175,175 # Change coordinates to the center of your print bed
+# speed: 50
+# z_hop: 10
+# z_hop_speed: 5
+
+#[bltouch]
+#sensor_pin: P1.26
+#control_pin: P2.4
+
+#[filament_switch_sensor my_sensor]
+#switch_pin: P1.27
+
+######################################################################
+# 128x64 Full Graphic Creality CR10 / ENDER 3 stockdisplay
+######################################################################
+
+[board_pins]
+aliases:
+    # EXP1 header
+    EXP1_1=P1.31, EXP1_3=P3.26, EXP1_5=P3.25, EXP1_7=P0.16, EXP1_9=<GND>,
+    EXP1_2=P1.30, EXP1_4=<RST>, EXP1_6=P0.15,  EXP1_8=P0.18, EXP1_10=<5V>