docs: Rename Documents
Signed-off-by: Yifei Ding <yifeiding@protonmail.com>
This commit is contained in:
Yifei Ding
Kevin O'Connor
parent
85667649d1
commit
a1af78cb83
|
|
@ -308,7 +308,7 @@ that command.
|
|||
|
||||
20190628: All configuration options have been removed from the
|
||||
[skew_correction] section. Configuration for skew_correction
|
||||
is now done via the SET_SKEW gcode. See skew_correction.md
|
||||
is now done via the SET_SKEW gcode. See [Skew Correction](Skew_Correction.md)
|
||||
for recommended usage.
|
||||
|
||||
20190607: The "variable_X" parameters of gcode_macro (along with the
|
||||
|
|
|
|||
|
|
@ -1112,8 +1112,8 @@ Printer Skew Correction. It is possible to use software to correct
|
|||
printer skew across 3 planes, xy, xz, yz. This is done by printing a
|
||||
calibration model along a plane and measuring three lengths. Due to
|
||||
the nature of skew correction these lengths are set via gcode. See
|
||||
[skew correction](skew_correction.md) and
|
||||
[command reference](G-Codes.md#skew-correction) for details.
|
||||
[Skew Correction](Skew_Correction.md) and
|
||||
[Command Reference](G-Codes.md#skew-correction) for details.
|
||||
|
||||
```
|
||||
[skew_correction]
|
||||
|
|
@ -3727,7 +3727,7 @@ TSLl401CL Based Filament Width Sensor. See the
|
|||
### [hall_filament_width_sensor]
|
||||
|
||||
Hall filament width sensor (see
|
||||
[Hall Filament Width Sensor](HallFilamentWidthSensor.md)).
|
||||
[Hall Filament Width Sensor](Hall_Filament_Width_Sensor.md)).
|
||||
|
||||
```
|
||||
[hall_filament_width_sensor]
|
||||
|
|
@ -3870,7 +3870,7 @@ vssa_pin:
|
|||
|
||||
### [replicape]
|
||||
|
||||
Replicape support - see the [beaglebone guide](beaglebone.md) and the
|
||||
Replicape support - see the [beaglebone guide](Beaglebone.md) and the
|
||||
[generic-replicape.cfg](../config/generic-replicape.cfg) file for an
|
||||
example.
|
||||
|
||||
|
|
|
|||
|
|
@ -136,7 +136,7 @@ feature when printing (see
|
|||
[config reference](Config_Reference.md#virtual_sdcard) for details).
|
||||
|
||||
For running on the Beaglebone, see the
|
||||
[Beaglebone specific installation instructions](beaglebone.md).
|
||||
[Beaglebone specific installation instructions](Beaglebone.md).
|
||||
|
||||
Klipper has been run on other machines. The Klipper host software only
|
||||
requires Python running on a Linux (or similar) computer. However, if
|
||||
|
|
|
|||
|
|
@ -663,7 +663,7 @@ retraction required.
|
|||
|
||||
The following commands are available when the
|
||||
[skew_correction config section](Config_Reference.md#skew_correction)
|
||||
is enabled (also see the [skew correction guide](skew_correction.md)):
|
||||
is enabled (also see the [Skew Correction](Skew_Correction.md) guide):
|
||||
- `SET_SKEW [XY=<ac_length,bd_length,ad_length>] [XZ=<ac,bd,ad>]
|
||||
[YZ=<ac,bd,ad>] [CLEAR=<0|1>]`: Configures the [skew_correction]
|
||||
module with measurements (in mm) taken from a calibration print.
|
||||
|
|
@ -678,7 +678,7 @@ is enabled (also see the [skew correction guide](skew_correction.md)):
|
|||
degrees) based on a measured print. This can be useful for
|
||||
determining the printer's current skew after correction has been
|
||||
applied. It may also be useful before correction is applied to
|
||||
determine if skew correction is necessary. See skew_correction.md
|
||||
determine if skew correction is necessary. See [Skew Correction](Skew_Correction.md)
|
||||
for details on skew calibration objects and measurements.
|
||||
- `SKEW_PROFILE [LOAD=<name>] [SAVE=<name>] [REMOVE=<name>]`: Profile
|
||||
management for skew_correction. LOAD will restore skew state from
|
||||
|
|
|
|||
|
|
@ -9,7 +9,7 @@ for other machines).
|
|||
Klipper currently supports a number of Atmel ATmega based
|
||||
micro-controllers,
|
||||
[ARM based micro-controllers](Features.md#step-benchmarks), and
|
||||
[Beaglebone PRU](beaglebone.md) based printers.
|
||||
[Beaglebone PRU](Beaglebone.md) based printers.
|
||||
|
||||
## Prepping an OS image
|
||||
|
||||
|
|
|
|||
|
|
@ -50,7 +50,7 @@ communication with the Klipper developers.
|
|||
with Klipper.
|
||||
- [Multi-MCU Homing](Multi_MCU_Homing.md): Homing and probing using multiple micro-controllers.
|
||||
- [Slicers](Slicers.md): Configure "slicer" software for Klipper.
|
||||
- [Skew correction](skew_correction.md): Adjustments for axes not
|
||||
- [Skew correction](Skew_Correction.md): Adjustments for axes not
|
||||
perfectly square.
|
||||
- [PWM tools](Using_PWM_Tools.md): Guide on how to use PWM controlled
|
||||
tools such as lasers or spindles.
|
||||
|
|
@ -85,10 +85,10 @@ communication with the Klipper developers.
|
|||
copying a binary to an sdcard in the micro-controller.
|
||||
- [Raspberry Pi as Micro-controller](RPi_microcontroller.md): Details
|
||||
for controlling devices wired to the GPIO pins of a Raspberry Pi.
|
||||
- [Beaglebone](beaglebone.md): Details for running Klipper on the
|
||||
- [Beaglebone](Beaglebone.md): Details for running Klipper on the
|
||||
Beaglebone PRU.
|
||||
- [Bootloaders](Bootloaders.md): Developer information on
|
||||
micro-controller flashing.
|
||||
- [CAN bus](CANBUS.md): Information on using CAN bus with Klipper.
|
||||
- [TSL1401CL filament width sensor](TSL1401CL_Filament_Width_Sensor.md)
|
||||
- [Hall filament width sensor](HallFilamentWidthSensor.md)
|
||||
- [Hall filament width sensor](Hall_Filament_Width_Sensor.md)
|
||||
|
|
|
|||
|
|
@ -101,7 +101,7 @@ nav:
|
|||
- TMC_Drivers.md
|
||||
- Multi_MCU_Homing.md
|
||||
- Slicers.md
|
||||
- skew_correction.md
|
||||
- Skew_Correction.md
|
||||
- Using_PWM_Tools.md
|
||||
- Developer Documentation:
|
||||
- Code_Overview.md
|
||||
|
|
@ -118,8 +118,8 @@ nav:
|
|||
- Example_Configs.md
|
||||
- SDCard_Updates.md
|
||||
- RPi_microcontroller.md
|
||||
- beaglebone.md
|
||||
- Beaglebone.md
|
||||
- Bootloaders.md
|
||||
- CANBUS.md
|
||||
- TSL1401CL_Filament_Width_Sensor.md
|
||||
- HallFilamentWidthSensor.md
|
||||
- Hall_Filament_Width_Sensor.md
|
||||
|
|
|
|||
Loading…
Reference in New Issue