config: Add config printer-sovol-sv05-2022.cfg (#6122)
Adding Sovol SV06 printer config Signed-off-by: Joseph Spainhour <spinixguy@gmail.com>
This commit is contained in:
parent
d8a9ab5ef7
commit
9fe3152e23
|
@ -0,0 +1,144 @@
|
||||||
|
# This file contains pin mappings for the stock 2022 Sovol SV05
|
||||||
|
# with the 32-bit Creality 4.2.2 board.
|
||||||
|
#
|
||||||
|
# To use this config, during "make menuconfig" select the STM32F103
|
||||||
|
# with a "28KiB bootloader" and serial (on USART1 PA10/PA9)
|
||||||
|
# communication.
|
||||||
|
#
|
||||||
|
# Flash this firmware by copying "out/klipper.bin" to a SD card and
|
||||||
|
# turning on the printer with the card inserted. The firmware
|
||||||
|
# filename must end in ".bin" and must not match the last filename
|
||||||
|
# that was flashed. Might need a renaming if printer dosnt flash.
|
||||||
|
|
||||||
|
# See docs/Config_Reference.md for a description of parameters.
|
||||||
|
[mcu]
|
||||||
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||||||
|
restart_method: command
|
||||||
|
|
||||||
|
[printer]
|
||||||
|
kinematics: cartesian
|
||||||
|
max_velocity: 300
|
||||||
|
max_accel: 1000
|
||||||
|
max_accel_to_decel: 1000
|
||||||
|
max_z_velocity: 5
|
||||||
|
max_z_accel: 100
|
||||||
|
|
||||||
|
[stepper_x]
|
||||||
|
step_pin: PC2
|
||||||
|
dir_pin: PB9
|
||||||
|
enable_pin: !PC3
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 40
|
||||||
|
endstop_pin: ^PA5
|
||||||
|
position_endstop: 220
|
||||||
|
position_max: 220
|
||||||
|
homing_speed: 50
|
||||||
|
position_min: -4
|
||||||
|
|
||||||
|
[stepper_y]
|
||||||
|
step_pin: PB8
|
||||||
|
dir_pin: PB7
|
||||||
|
enable_pin: !PC3
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 40
|
||||||
|
endstop_pin: ^PA6
|
||||||
|
position_endstop: 220
|
||||||
|
position_max: 220
|
||||||
|
position_min: -4
|
||||||
|
homing_speed: 50
|
||||||
|
|
||||||
|
[stepper_z]
|
||||||
|
step_pin: PB6
|
||||||
|
dir_pin: PB5
|
||||||
|
enable_pin: !PC3
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 8
|
||||||
|
endstop_pin: probe:z_virtual_endstop
|
||||||
|
position_max: 300
|
||||||
|
position_min: -3
|
||||||
|
|
||||||
|
[heater_bed]
|
||||||
|
heater_pin: PA2
|
||||||
|
sensor_type: EPCOS 100K B57560G104F
|
||||||
|
sensor_pin: PC4
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 130
|
||||||
|
control: pid
|
||||||
|
pid_kp: 64.742
|
||||||
|
pid_ki: 0.827
|
||||||
|
pid_kd: 1267.326
|
||||||
|
|
||||||
|
[fan]
|
||||||
|
pin: PA0
|
||||||
|
|
||||||
|
[safe_z_home]
|
||||||
|
home_xy_position: 70, 103
|
||||||
|
speed: 100
|
||||||
|
z_hop: 10
|
||||||
|
z_hop_speed: 20
|
||||||
|
|
||||||
|
[extruder]
|
||||||
|
step_pin: PB4
|
||||||
|
dir_pin: PB3
|
||||||
|
enable_pin: !PC3
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 7.394
|
||||||
|
nozzle_diameter: 0.400
|
||||||
|
filament_diameter: 1.750
|
||||||
|
max_extrude_only_distance: 100.0
|
||||||
|
heater_pin: PA1
|
||||||
|
sensor_type: EPCOS 100K B57560G104F
|
||||||
|
sensor_pin: PC5
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 280
|
||||||
|
control: pid
|
||||||
|
pid_kp: 28.850
|
||||||
|
pid_ki: 1.658
|
||||||
|
pid_kd: 125.496
|
||||||
|
|
||||||
|
[bltouch]
|
||||||
|
sensor_pin: ^PB1
|
||||||
|
control_pin: PB0
|
||||||
|
z_offset: 0
|
||||||
|
x_offset: 40
|
||||||
|
y_offset: 7
|
||||||
|
samples: 2
|
||||||
|
samples_tolerance: 0.015
|
||||||
|
samples_tolerance_retries: 5
|
||||||
|
|
||||||
|
[bed_mesh]
|
||||||
|
speed: 100
|
||||||
|
horizontal_move_z: 5
|
||||||
|
mesh_min: 40, 7
|
||||||
|
mesh_max: 220, 220
|
||||||
|
probe_count: 5, 5
|
||||||
|
algorithm: bicubic
|
||||||
|
fade_start: 1
|
||||||
|
fade_end: 10
|
||||||
|
|
||||||
|
[bed_screws]
|
||||||
|
screw1: 25,28
|
||||||
|
screw2: 195,28
|
||||||
|
screw3: 195,197
|
||||||
|
screw4: 25,197
|
||||||
|
|
||||||
|
[screws_tilt_adjust]
|
||||||
|
screw1: -4,21
|
||||||
|
screw1_name: front left screw
|
||||||
|
screw2: 155,21
|
||||||
|
screw2_name: front right screw
|
||||||
|
screw3: 155,190
|
||||||
|
screw3_name: rear right screw
|
||||||
|
screw4: -4,190
|
||||||
|
screw4_name: rear left screw
|
||||||
|
horizontal_move_z: 10
|
||||||
|
speed: 50
|
||||||
|
screw_thread: CW-M4
|
||||||
|
|
||||||
|
[display]
|
||||||
|
lcd_type: st7920
|
||||||
|
cs_pin: PB12
|
||||||
|
sclk_pin: PB13
|
||||||
|
sid_pin: PB15
|
||||||
|
encoder_pins: ^PB14, ^PB10
|
||||||
|
click_pin: ^!PB2
|
|
@ -154,6 +154,7 @@ CONFIG ../../config/generic-bigtreetech-skr-mini-e3-v2.0.cfg
|
||||||
CONFIG ../../config/generic-bigtreetech-skr-mini-mz.cfg
|
CONFIG ../../config/generic-bigtreetech-skr-mini-mz.cfg
|
||||||
CONFIG ../../config/printer-anycubic-vyper-2021.cfg
|
CONFIG ../../config/printer-anycubic-vyper-2021.cfg
|
||||||
CONFIG ../../config/printer-monoprice-select-mini-v1-2016.cfg
|
CONFIG ../../config/printer-monoprice-select-mini-v1-2016.cfg
|
||||||
|
CONFIG ../../config/printer-sovol-sv05-2022.cfg
|
||||||
CONFIG ../../config/printer-sovol-sv06-2022.cfg
|
CONFIG ../../config/printer-sovol-sv06-2022.cfg
|
||||||
CONFIG ../../config/printer-sunlu-t3-2022.cfg
|
CONFIG ../../config/printer-sunlu-t3-2022.cfg
|
||||||
|
|
||||||
|
|
Loading…
Reference in New Issue