config: Add periods to end of sentences in example configs
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
c9b6662138
commit
944c121a00
|
@ -8,7 +8,7 @@
|
|||
# FIRST. Incorrectly configured parameters may cause damage.
|
||||
|
||||
# The stepper_x section is used to describe the X axis as well as the
|
||||
# stepper controlling the X+Y movement
|
||||
# stepper controlling the X+Y movement.
|
||||
[stepper_x]
|
||||
step_pin: ar54
|
||||
dir_pin: ar55
|
||||
|
@ -21,7 +21,7 @@ position_endstop: 0
|
|||
position_max: 200
|
||||
|
||||
# The stepper_y section is used to describe the Y axis as well as the
|
||||
# stepper controlling the X-Y movement
|
||||
# stepper controlling the X-Y movement.
|
||||
[stepper_y]
|
||||
step_pin: ar60
|
||||
dir_pin: ar61
|
||||
|
|
|
@ -20,7 +20,7 @@ homing_speed: 50.0
|
|||
position_endstop: 297.05
|
||||
|
||||
# The stepper_b section describes the stepper controlling the front
|
||||
# right tower (at 330 degrees)
|
||||
# right tower (at 330 degrees).
|
||||
[stepper_b]
|
||||
step_pin: ar60
|
||||
dir_pin: ar61
|
||||
|
@ -30,7 +30,7 @@ endstop_pin: ^ar15
|
|||
position_endstop: 297.05
|
||||
|
||||
# The stepper_c section describes the stepper controlling the rear
|
||||
# tower (at 90 degrees)
|
||||
# tower (at 90 degrees).
|
||||
[stepper_c]
|
||||
step_pin: ar46
|
||||
dir_pin: ar48
|
||||
|
@ -64,7 +64,7 @@ control: watermark
|
|||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
# Extruder print fan (omit section if fan not present)
|
||||
# Extruder print fan (omit section if fan not present).
|
||||
#[fan]
|
||||
#pin: ar9
|
||||
|
||||
|
|
|
@ -18,7 +18,7 @@
|
|||
|
||||
|
||||
# The stepper_x section is used to describe the stepper controlling
|
||||
# the X axis in a cartesian robot
|
||||
# the X axis in a cartesian robot.
|
||||
[stepper_x]
|
||||
step_pin: ar29
|
||||
# Step GPIO pin (triggered high). This parameter must be provided.
|
||||
|
@ -77,7 +77,7 @@ position_max: 200
|
|||
|
||||
# The stepper_y section is used to describe the stepper controlling
|
||||
# the Y axis in a cartesian robot. It has the same settings as the
|
||||
# stepper_x section
|
||||
# stepper_x section.
|
||||
[stepper_y]
|
||||
step_pin: ar27
|
||||
dir_pin: ar26
|
||||
|
@ -90,7 +90,7 @@ position_max: 200
|
|||
|
||||
# The stepper_z section is used to describe the stepper controlling
|
||||
# the Z axis in a cartesian robot. It has the same settings as the
|
||||
# stepper_x section
|
||||
# stepper_x section.
|
||||
[stepper_z]
|
||||
step_pin: ar23
|
||||
dir_pin: !ar22
|
||||
|
@ -105,7 +105,7 @@ position_max: 200
|
|||
# controlling the printer extruder and the heater parameters for the
|
||||
# nozzle. The stepper configuration has the same settings as the
|
||||
# stepper_x section and the heater configuration has the same settings
|
||||
# as the heater_bed section
|
||||
# as the heater_bed section (described below).
|
||||
[extruder]
|
||||
step_pin: ar19
|
||||
dir_pin: ar18
|
||||
|
@ -151,7 +151,7 @@ filament_diameter: 3.500
|
|||
# buildup. This setting only applies if pressure_advance is
|
||||
# non-zero. The default is 0.010 (10 milliseconds).
|
||||
#
|
||||
# The remaining variables describe the extruder heater
|
||||
# The remaining variables describe the extruder heater.
|
||||
heater_pin: ar4
|
||||
# PWM output pin controlling the heater. This parameter must be
|
||||
# provided.
|
||||
|
@ -219,7 +219,7 @@ control: watermark
|
|||
min_temp: 0
|
||||
max_temp: 110
|
||||
|
||||
# Extruder print fan (omit section if fan not present)
|
||||
# Extruder print fan (omit section if fan not present).
|
||||
[fan]
|
||||
pin: ar14
|
||||
# PWM output pin controlling the fan. This parameter must be
|
||||
|
@ -234,7 +234,7 @@ pin: ar14
|
|||
# Time (in seconds) to run the fan at full speed when first enabling
|
||||
# it (helps get the fan spinning). The default is 0.100 seconds.
|
||||
|
||||
# Micro-controller information
|
||||
# Micro-controller information.
|
||||
[mcu]
|
||||
serial: /dev/ttyACM0
|
||||
# The serial port to connect to the MCU. The default is /dev/ttyS0
|
||||
|
@ -260,7 +260,7 @@ custom:
|
|||
# LEDs, to configure micro-stepping pins, to configure a digipot,
|
||||
# etc.
|
||||
|
||||
# The printer section controls high level printer settings
|
||||
# The printer section controls high level printer settings.
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
# This option must be "cartesian" for cartesian printers.
|
||||
|
|
Loading…
Reference in New Issue