diff --git a/config/printer-twotrees-sapphire-pro-2020.cfg b/config/printer-twotrees-sapphire-pro-2020.cfg
new file mode 100644
index 00000000..4c9b4c51
--- /dev/null
+++ b/config/printer-twotrees-sapphire-pro-2020.cfg
@@ -0,0 +1,89 @@
+# This file contains common pin mappings for the Two Trees Sapphire
+# Pro printer from 2020. To use this config, the firmware should be
+# compiled for the STM32F103. When running "make menuconfig", enable
+# "extra low-level configuration setup", select the 28KiB bootloader,
+# disable "USB for communication", select USART3 for the "Serial
+# Port", and set "GPIO pins to set at micro-controller startup" to
+# "!PC6,!PD13".
+
+# Note that the "make flash" command does not work with the Sapphire
+# Pro. After running "make", run the following command:
+#   ./scripts/update_mks_robin.py out/klipper.bin out/Robin_nano35.bin
+# Copy the file out/Robin_nano35.bin to an SD card and then restart the
+# printer with that SD card.
+
+# See the example.cfg file for a description of available parameters.
+
+[stepper_x]
+step_pin: PE3
+dir_pin: !PE2
+enable_pin: !PE4
+step_distance: .01
+endstop_pin: !PA15
+position_endstop: 0
+position_max: 230
+homing_speed: 50
+
+[stepper_y]
+step_pin: PE0
+dir_pin: !PB9
+enable_pin: !PE1
+step_distance: .01
+endstop_pin: !PA12
+position_endstop: 230
+position_max: 230
+homing_speed: 50
+
+[stepper_z]
+step_pin: PB5
+dir_pin: PB4
+enable_pin: !PB8
+step_distance: .0025
+endstop_pin: !PA11
+position_endstop: 0.5
+position_max: 230
+
+[extruder]
+step_pin: PD6
+dir_pin: !PD3
+enable_pin: !PB3
+step_distance: .0021
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PC3
+sensor_type: ATC Semitec 104GT-2
+sensor_pin: PC1
+control: pid
+pid_Kp: 14.669
+pid_Ki: 0.572
+pid_Kd: 94.068
+min_temp: 0
+max_temp: 250
+
+[heater_bed]
+heater_pin: PA0
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC0
+control: pid
+pid_Kp: 325.10
+pid_Ki: 63.35
+pid_Kd: 417.10
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: PB1
+
+[mcu]
+serial: /dev/ttyUSB0
+restart_method: command
+
+[printer]
+kinematics: corexy
+max_velocity: 250
+max_accel: 4500
+max_z_velocity: 25
+max_z_accel: 100
+
+[static_digital_output reset_display]
+pins: !PC6, !PD13
diff --git a/test/klippy/printers.test b/test/klippy/printers.test
index 698ae30f..2875a14b 100644
--- a/test/klippy/printers.test
+++ b/test/klippy/printers.test
@@ -114,6 +114,7 @@ DICTIONARY stm32f103-serial.dict
 CONFIG ../../config/generic-fysetc-cheetah-v1.1.cfg
 CONFIG ../../config/generic-fysetc-cheetah-v1.2.cfg
 CONFIG ../../config/generic-mks-robin-nano.cfg
+CONFIG ../../config/printer-twotrees-sapphire-pro-2020.cfg
 
 # Printers using the stm32f407
 DICTIONARY stm32f407.dict