config: add Flsun Q5 config (#3915)
In cooperation with chaosdrucker Signed-off-by: Christoph Frei <fryakatkop@gmail.com>
This commit is contained in:
parent
2aa2e91f2c
commit
8f52816419
|
@ -0,0 +1,113 @@
|
|||
# This file contains common configurations and pin mappings
|
||||
# for the Flsun Q5 using the MKS Robin Nano board.
|
||||
|
||||
# To use this config, the firmware should be compiled for the
|
||||
# STM32F103. When running "make menuconfig", enable "extra low-level
|
||||
# configuration setup", select the 28KiB bootloader, disable "USB for
|
||||
# communication", and select USART3 for the "Serial Port".
|
||||
|
||||
# Note that the "make flash" command does not work with MKS Robin
|
||||
# boards. After running "make", run the following command:
|
||||
# ./scripts/update_mks_robin.py out/klipper.bin out/Robin_nano.bin
|
||||
# Copy the file out/Robin_nano.bin to an SD card and then restart the
|
||||
# printer with that SD card.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||||
restart_method: command
|
||||
|
||||
[printer]
|
||||
kinematics: delta
|
||||
max_velocity: 250
|
||||
max_accel: 7000
|
||||
max_accel_to_decel: 7000
|
||||
max_z_velocity: 100
|
||||
delta_radius: 107.5
|
||||
print_radius: 100
|
||||
minimum_z_position: -25
|
||||
|
||||
[stepper_a]
|
||||
step_pin: PE3
|
||||
dir_pin: PE2
|
||||
enable_pin: !PE4
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: PA15
|
||||
homing_speed: 20
|
||||
homing_retract_dist: 5
|
||||
homing_retract_speed: 10
|
||||
second_homing_speed: 2
|
||||
position_endstop: 207
|
||||
arm_length: 215
|
||||
angle: 210
|
||||
|
||||
[stepper_b]
|
||||
step_pin: PE0
|
||||
dir_pin: PB9
|
||||
enable_pin: !PE1
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: PA12
|
||||
angle: 330
|
||||
|
||||
[stepper_c]
|
||||
step_pin: PB5
|
||||
dir_pin: PB4
|
||||
enable_pin: !PB8
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: PC4
|
||||
angle: 90
|
||||
|
||||
[probe]
|
||||
pin: !PA11
|
||||
x_offset: 0
|
||||
y_offset: 0
|
||||
z_offset: 20.26
|
||||
speed: 5.0
|
||||
samples: 5
|
||||
samples_result: average
|
||||
sample_retract_dist: 3
|
||||
samples_tolerance: 0.02
|
||||
samples_tolerance_retries: 5
|
||||
|
||||
[delta_calibrate]
|
||||
radius: 95
|
||||
horizontal_move_z: 25
|
||||
Speed: 10
|
||||
|
||||
[extruder]
|
||||
step_pin: PD6
|
||||
dir_pin: !PD3
|
||||
enable_pin: !PB3
|
||||
microsteps: 16
|
||||
rotation_distance: 22.17
|
||||
gear_ratio: 66:22
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PC3
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC1
|
||||
control: pid
|
||||
pid_kp: 14.529
|
||||
pid_ki: 0.557
|
||||
pid_kd: 94.802
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
max_extrude_only_distance: 110.0
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PA0
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC0
|
||||
control: pid
|
||||
pid_Kp: 325.10
|
||||
pid_Ki: 63.35
|
||||
pid_Kd: 417.10
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PB1
|
Loading…
Reference in New Issue