diff --git a/config/generic-mks-monster8.cfg b/config/generic-mks-monster8.cfg
new file mode 100644
index 00000000..583d49bf
--- /dev/null
+++ b/config/generic-mks-monster8.cfg
@@ -0,0 +1,268 @@
+# This file contains common pin mappings for MKS Monster8
+# boards. To use this config, the firmware should be compiled for the
+# stm32f407. When running "make menuconfig", select the 48KiB
+# bootloader, and enable "USB for communication".
+
+# The "make flash" command does not work on the MKS Monster8. Instead,
+# after running "make", copy the generated "out/klipper.bin" file to a
+# file named "mks_monster8.bin" on an SD card or Udisk and then restart the
+# MKS Monster8 with that SD card or Udisk.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[stepper_x]
+step_pin: PC14
+dir_pin: PC13
+enable_pin: !PC15
+microsteps: 16
+rotation_distance: 40
+endstop_pin: !PA14  # PA13 for X-max; endstop have'!' is NO
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+[stepper_y]
+step_pin: PE5
+dir_pin: !PE4
+enable_pin: !PC15
+microsteps: 16
+rotation_distance: 40
+endstop_pin: !PA15  # PC5 for Y-max; endstop have'!' is NO
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+[stepper_z]
+step_pin: PE1
+dir_pin: PE0
+enable_pin: !PE2
+microsteps: 16
+rotation_distance: 8
+endstop_pin: !PB13  # PB12 for Z-max; endstop have'!' is NO
+position_endstop: 0
+position_max: 220
+
+[extruder]
+step_pin: PB5
+dir_pin: !PB4
+enable_pin: !PB6
+microsteps: 16
+rotation_distance: 33.500
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PB1
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC1
+control: pid
+pid_Kp: 22
+pid_Ki: 1.08
+pid_Kd: 114
+min_temp: 0
+max_temp: 260
+
+#[extruder1]
+#step_pin: PD6
+#dir_pin: !PD5
+#enable_pin: !PD7
+#heater_pin: PB0
+#sensor_pin: PC2
+
+#[extruder2]
+#step_pin: PD2
+#dir_pin: !PD1
+#enable_pin: !PD3
+#heater_pin: PA3
+#sensor_pin: PC3
+
+#[extruder3]
+#step_pin: PC7
+#dir_pin: PC6
+#enable_pin: !PC8
+
+#[extruder4]
+#step_pin: PD13
+#dir_pin: !PD12
+#enable_pin: !PD14
+
+[heater_bed]
+heater_pin: PB10
+sensor_type: NTC 100K MGB18-104F39050L32
+sensor_pin: PC0
+max_power: 1.0
+control: pid
+pid_kp: 71.039
+pid_ki: 2.223
+pid_kd: 567.421
+min_temp: 0
+max_temp: 200
+
+#fan for printed model FAN0
+[fan]
+pin: PA2
+
+#fan for hotend FAN1
+#[heater_fan my_nozzle_fan]
+[heater_fan fan1]
+pin: PA1
+shutdown_speed: 1
+
+#fan for control board FAN2
+#[heater_fan my_control_fan]
+[heater_fan fan2]
+pin: PA0
+shutdown_speed: 1
+
+[mcu]
+serial: /dev/serial/by-id/usb-Klipper_stm32f407xx_4D0045001850314335393520-if00
+
+[printer]
+kinematics: cartesian
+max_velocity: 10000
+max_accel: 20000
+max_z_velocity: 100
+max_z_accel: 1000
+
+#####################################################################
+# LED Control
+#####################################################################
+
+#[output_pin caselight ](Use PA9)
+##  Chamber Lighting - In 5V-RGB Position
+#pin: PA9
+#pwm: true
+#shutdown_value: 0
+#value:100
+#cycle_time: 0.01
+
+########################################
+# TMC UART configuration
+########################################
+
+#[tmc2208 stepper_x]
+#uart_pin: PE6
+#run_current: 0.8
+#hold_current: 0.5
+#stealthchop_threshold: 999999
+
+#[tmc2208 stepper_y]
+#uart_pin: PE3
+#run_current: 0.8
+#hold_current: 0.5
+#stealthchop_threshold: 999999
+
+#[tmc2208 stepper_z]
+#uart_pin: PB7
+#run_current: 0.8
+#hold_current: 0.5
+#stealthchop_threshold: 999999
+
+#[tmc2208 extruder]
+#uart_pin: PB3
+#run_current: 0.8
+#hold_current: 0.5
+#sense_resistor: 0.110
+#stealthchop_threshold: 999999
+
+#[tmc2208 extruder1]
+#uart_pin: PD4
+#run_current: 0.8
+#hold_current: 0.5
+#stealthchop_threshold: 999999
+
+#[tmc2208 extruder2]
+#uart_pin: PD0
+#run_current: 0.8
+#hold_current: 0.5
+#stealthchop_threshold: 999999
+
+#[tmc2208 extruder3]
+#uart_pin: PD15
+#run_current: 0.8
+#hold_current: 0.5
+#stealthchop_threshold: 999999
+
+#[tmc2208 extruder4]
+#uart_pin: PD11
+#run_current: 0.8
+#hold_current: 0.5
+#stealthchop_threshold: 999999
+
+########################################
+# TMC SPI configuration
+########################################
+
+#[tmc2130 stepper_x]
+#spi_bus: spi4
+#cs_pin: PE6
+#diag1_pin: PA14
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 999999
+
+#[tmc2130 stepper_y]
+#spi_bus: spi4
+#cs_pin: PE3
+#diag1_pin: PA15
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 999999
+
+#[tmc2130 stepper_z]
+#spi_bus: spi4
+#cs_pin: PB7
+#diag1_pin: PB13
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 999999
+
+#[tmc2130 extruder]
+#spi_bus: spi4
+#cs_pin: PB3
+#diag1_pin: PA13
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 999999
+
+#[tmc2130 extruder1]
+#spi_bus: spi4
+#cs_pin: PD4
+#diag1_pin: PC5
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 999999
+
+#[tmc2130 extruder2]
+#spi_bus: spi4
+#cs_pin: PD0
+#diag1_pin: PB12
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 999999
+
+#[tmc2130 extruder3]
+#spi_bus: spi4
+#cs_pin: PD15
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 999999
+
+#[tmc2130 extruder4]
+#spi_bus: spi4
+#cs_pin: PD11
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 999999
+
+########################################
+# EXP1 / EXP2 (display) pins
+########################################
+
+[board_pins]
+aliases:
+    # EXP1 header
+    EXP1_1=PB2,  EXP1_3=PE11, EXP1_5=PD9, EXP1_7=PE15, EXP1_9=<GND>,
+    EXP1_2=PE10, EXP1_4=PD10, EXP1_6=PD8, EXP1_8=PE7,  EXP1_10=<5V>,
+    # EXP2 header
+    EXP2_1=PA6, EXP2_3=PE9, EXP2_5=PE8, EXP2_7=PB11,  EXP2_9=<GND>,
+    EXP2_2=PA5, EXP2_4=PA4, EXP2_6=PA7, EXP2_8=<RST>, EXP2_10=<3.3v>
+    # Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "ssp1"
diff --git a/test/klippy/printers.test b/test/klippy/printers.test
index 28c172ae..8038ad4c 100644
--- a/test/klippy/printers.test
+++ b/test/klippy/printers.test
@@ -220,6 +220,7 @@ CONFIG ../../config/generic-bigtreetech-skr-2.cfg
 CONFIG ../../config/generic-flyboard.cfg
 CONFIG ../../config/generic-mellow-fly-cdy-v3.cfg
 CONFIG ../../config/generic-mellow-super-infinty-hv.cfg
+CONFIG ../../config/generic-mks-monster8.cfg
 CONFIG ../../config/generic-mks-robin-nano-v3.cfg
 CONFIG ../../config/generic-prusa-buddy.cfg
 CONFIG ../../config/generic-th3d-ezboard-v2.0.cfg