config: Add Creality Ender 5 2019

This config is based on the existing Ender 3 example config but some of 
the directions for the steppers have been reversed. It works for me so 
far, but feel free to modify.

Signed-off-by: Billy Jones <billyajones@gmail.com>
This commit is contained in:
Billy Jones 2019-04-28 19:23:20 -07:00 committed by KevinOConnor
parent a0f2d54743
commit 8d19351ea0
1 changed files with 93 additions and 0 deletions

View File

@ -0,0 +1,93 @@
# This file contains common pin mappings for the 2019 Creality
# Ender 5. To use this config, the firmware should be compiled for the
# AVR atmega1284p.
# Note, a number of Melzi boards are shipped with a bootloader that
# requires the following command to flash the board:
# avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex
# If the above command does not work and "make flash" does not work
# then one may need to flash a bootloader to the board - see the
# Klipper docs/Bootloaders.md file for more information.
# See the example.cfg file for a description of available parameters.
[stepper_x]
step_pin: PD7
dir_pin: PC5
enable_pin: !PD6
step_distance: .0125
endstop_pin: ^PC2
position_endstop: 0
position_max: 235
homing_speed: 30
[stepper_y]
step_pin: PC6
dir_pin: PC7
enable_pin: !PD6
step_distance: .0125
endstop_pin: ^PC3
position_endstop: 0
position_max: 235
homing_speed: 30
[stepper_z]
step_pin: PB3
dir_pin: !PB2
enable_pin: !PA5
step_distance: .0025
endstop_pin: ^PC4
position_endstop: 0.0
position_max: 300
[extruder]
max_extrude_only_distance: 100.0
step_pin: PB1
dir_pin: !PB0
enable_pin: !PD6
step_distance: 0.010526
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PD5
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA7
control: pid
# tuned for stock hardware with 200 degree Celsius target
pid_Kp: 21.527
pid_Ki: 1.063
pid_Kd: 108.982
min_temp: 0
max_temp: 250
[heater_bed]
heater_pin: PD4
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA6
control: pid
# tuned for stock hardware with 50 degree Celsius target
pid_Kp: 54.027
pid_Ki: 0.770
pid_Kd: 948.182
min_temp: 0
max_temp: 130
[fan]
pin: PB4
[mcu]
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
[display]
lcd_type: st7920
cs_pin: PA3
sclk_pin: PA1
sid_pin: PC1
encoder_pins: ^PD2, ^PD3
click_pin: ^!PC0