config: Add Creality Ender 5 2019
This config is based on the existing Ender 3 example config but some of the directions for the steppers have been reversed. It works for me so far, but feel free to modify. Signed-off-by: Billy Jones <billyajones@gmail.com>
This commit is contained in:
parent
a0f2d54743
commit
8d19351ea0
|
@ -0,0 +1,93 @@
|
|||
# This file contains common pin mappings for the 2019 Creality
|
||||
# Ender 5. To use this config, the firmware should be compiled for the
|
||||
# AVR atmega1284p.
|
||||
|
||||
# Note, a number of Melzi boards are shipped with a bootloader that
|
||||
# requires the following command to flash the board:
|
||||
# avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex
|
||||
# If the above command does not work and "make flash" does not work
|
||||
# then one may need to flash a bootloader to the board - see the
|
||||
# Klipper docs/Bootloaders.md file for more information.
|
||||
|
||||
# See the example.cfg file for a description of available parameters.
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PD7
|
||||
dir_pin: PC5
|
||||
enable_pin: !PD6
|
||||
step_distance: .0125
|
||||
endstop_pin: ^PC2
|
||||
position_endstop: 0
|
||||
position_max: 235
|
||||
homing_speed: 30
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PC6
|
||||
dir_pin: PC7
|
||||
enable_pin: !PD6
|
||||
step_distance: .0125
|
||||
endstop_pin: ^PC3
|
||||
position_endstop: 0
|
||||
position_max: 235
|
||||
homing_speed: 30
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB3
|
||||
dir_pin: !PB2
|
||||
enable_pin: !PA5
|
||||
step_distance: .0025
|
||||
endstop_pin: ^PC4
|
||||
position_endstop: 0.0
|
||||
position_max: 300
|
||||
|
||||
[extruder]
|
||||
max_extrude_only_distance: 100.0
|
||||
step_pin: PB1
|
||||
dir_pin: !PB0
|
||||
enable_pin: !PD6
|
||||
step_distance: 0.010526
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PD5
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PA7
|
||||
control: pid
|
||||
# tuned for stock hardware with 200 degree Celsius target
|
||||
pid_Kp: 21.527
|
||||
pid_Ki: 1.063
|
||||
pid_Kd: 108.982
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PD4
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PA6
|
||||
control: pid
|
||||
# tuned for stock hardware with 50 degree Celsius target
|
||||
pid_Kp: 54.027
|
||||
pid_Ki: 0.770
|
||||
pid_Kd: 948.182
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PB4
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[display]
|
||||
lcd_type: st7920
|
||||
cs_pin: PA3
|
||||
sclk_pin: PA1
|
||||
sid_pin: PC1
|
||||
encoder_pins: ^PD2, ^PD3
|
||||
click_pin: ^!PC0
|
Loading…
Reference in New Issue