From 8d19351ea0e314b81a0ff0ece9960c59e17f0294 Mon Sep 17 00:00:00 2001
From: Billy Jones <billyajones@gmail.com>
Date: Sun, 28 Apr 2019 19:23:20 -0700
Subject: [PATCH] config: Add Creality Ender 5 2019

This config is based on the existing Ender 3 example config but some of
the directions for the steppers have been reversed. It works for me so
far, but feel free to modify.

Signed-off-by: Billy Jones <billyajones@gmail.com>
---
 config/printer-creality-ender5-2019.cfg | 93 +++++++++++++++++++++++++
 1 file changed, 93 insertions(+)
 create mode 100644 config/printer-creality-ender5-2019.cfg

diff --git a/config/printer-creality-ender5-2019.cfg b/config/printer-creality-ender5-2019.cfg
new file mode 100644
index 00000000..3e67bd07
--- /dev/null
+++ b/config/printer-creality-ender5-2019.cfg
@@ -0,0 +1,93 @@
+# This file contains common pin mappings for the 2019 Creality
+# Ender 5. To use this config, the firmware should be compiled for the
+# AVR atmega1284p.
+
+# Note, a number of Melzi boards are shipped with a bootloader that
+# requires the following command to flash the board:
+#  avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex
+# If the above command does not work and "make flash" does not work
+# then one may need to flash a bootloader to the board - see the
+# Klipper docs/Bootloaders.md file for more information.
+
+# See the example.cfg file for a description of available parameters.
+
+[stepper_x]
+step_pin: PD7
+dir_pin: PC5
+enable_pin: !PD6
+step_distance: .0125
+endstop_pin: ^PC2
+position_endstop: 0
+position_max: 235
+homing_speed: 30
+
+[stepper_y]
+step_pin: PC6
+dir_pin: PC7
+enable_pin: !PD6
+step_distance: .0125
+endstop_pin: ^PC3
+position_endstop: 0
+position_max: 235
+homing_speed: 30
+
+[stepper_z]
+step_pin: PB3
+dir_pin: !PB2
+enable_pin: !PA5
+step_distance: .0025
+endstop_pin: ^PC4
+position_endstop: 0.0
+position_max: 300
+
+[extruder]
+max_extrude_only_distance: 100.0
+step_pin: PB1
+dir_pin: !PB0
+enable_pin: !PD6
+step_distance: 0.010526
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PD5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PA7
+control: pid
+# tuned for stock hardware with 200 degree Celsius target
+pid_Kp: 21.527
+pid_Ki: 1.063
+pid_Kd: 108.982
+min_temp: 0
+max_temp: 250
+
+[heater_bed]
+heater_pin: PD4
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PA6
+control: pid
+# tuned for stock hardware with 50 degree Celsius target
+pid_Kp: 54.027
+pid_Ki: 0.770
+pid_Kd: 948.182
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: PB4
+
+[mcu]
+serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 5
+max_z_accel: 100
+
+[display]
+lcd_type: st7920
+cs_pin: PA3
+sclk_pin: PA1
+sid_pin: PC1
+encoder_pins: ^PD2, ^PD3
+click_pin: ^!PC0