3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

config: Change default pins defined in example.cfg to use RAMPS pins 

Change the example.cfg file to use the pins of a RAMPS config as that
is a very common setup.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
Kevin O'Connor 2017-07-24 12:34:26 -04:00
parent 51baeb3c2c
commit 85a1e1118f
2 changed files with 27 additions and 32 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

9
config/example-corexy.cfg
View File

@ -14,9 +14,8 @@ step_pin: ar54
dir_pin: ar55
enable_pin: !ar38
step_distance: .01
endstop_pin: ^ar2
endstop_pin: ^ar3
homing_speed: 50.0
position_min: 0
position_endstop: 0
position_max: 200
@ -27,9 +26,8 @@ step_pin: ar60
dir_pin: ar61
enable_pin: !ar56
step_distance: .01
endstop_pin: ^ar15
endstop_pin: ^ar14
homing_speed: 50.0
position_min: 0
position_endstop: 0
position_max: 200
@ -38,8 +36,7 @@ step_pin: ar46
dir_pin: ar48
enable_pin: !ar62
step_distance: .01
endstop_pin: ^ar19
position_min: 0.1
endstop_pin: ^ar18
position_endstop: 0.5
position_max: 200

50
config/example.cfg
View File

@ -20,19 +20,19 @@
# The stepper_x section is used to describe the stepper controlling
# the X axis in a cartesian robot.
[stepper_x]
step_pin: ar29
step_pin: ar54
# Step GPIO pin (triggered high). This parameter must be provided.
dir_pin: !ar28
dir_pin: ar55
# Direction GPIO pin (high indicates positive direction). This
# parameter must be provided.
enable_pin: !ar25
enable_pin: !ar38
# Enable pin (default is enable high; use ! to indicate enable
# low). If this parameter is not provided then the stepper motor
# driver must always be enabled.
step_distance: .0225
# Distance in mm that each step causes the axis to travel. This
# parameter must be provided.
endstop_pin: ^ar0
endstop_pin: ^ar3
# Endstop switch detection pin. This parameter must be provided for
# the X, Y, and Z steppers on cartesian style printers.
#homing_speed: 5.0
@ -64,7 +64,7 @@ endstop_pin: ^ar0
# reset. If this is not set, but homing_stepper_phases is set, then
# the stepper phase will be detected on the first home and that
# phase will be used on all subsequent homes.
position_min: -0.25
#position_min: 0
# Minimum valid distance (in mm) the user may command the stepper to
# move to. The default is 0mm.
position_endstop: 0
@ -79,12 +79,11 @@ position_max: 200
# the Y axis in a cartesian robot. It has the same settings as the
# stepper_x section.
[stepper_y]
step_pin: ar27
dir_pin: ar26
enable_pin: !ar25
step_pin: ar60
dir_pin: !ar61
enable_pin: !ar56
step_distance: .0225
endstop_pin: ^ar1
position_min: -0.25
endstop_pin: ^ar14
position_endstop: 0
position_max: 200
@ -92,12 +91,11 @@ position_max: 200
# the Z axis in a cartesian robot. It has the same settings as the
# stepper_x section.
[stepper_z]
step_pin: ar23
dir_pin: !ar22
enable_pin: !ar25
step_pin: ar46
dir_pin: ar48
enable_pin: !ar62
step_distance: .005
endstop_pin: ^ar2
position_min: 0.1
endstop_pin: ^ar18
position_endstop: 0.5
position_max: 200
@ -107,9 +105,9 @@ position_max: 200
# stepper_x section and the heater configuration has the same settings
# as the heater_bed section (described below).
[extruder]
step_pin: ar19
dir_pin: ar18
enable_pin: !ar25
step_pin: ar26
dir_pin: ar28
enable_pin: !ar24
step_distance: .004242
nozzle_diameter: 0.500
# Diameter of the nozzle orifice (in mm). This parameter must be
@ -164,7 +162,7 @@ filament_diameter: 3.500
# activation.
#
# The remaining variables describe the extruder heater.
heater_pin: ar4
heater_pin: ar10
# PWM output pin controlling the heater. This parameter must be
# provided.
#max_power: 1.0
@ -177,7 +175,7 @@ heater_pin: ar4
sensor_type: EPCOS 100K B57560G104F
# Type of sensor - this may be "EPCOS 100K B57560G104F", "ATC
# Semitec 104GT-2", or "AD595". This parameter must be provided.
sensor_pin: analog1
sensor_pin: analog13
# Analog input pin connected to the sensor. This parameter must be
# provided.
#pullup_resistor: 4700
@ -221,16 +219,16 @@ max_temp: 210
# named "extruder1", "extruder2", "extruder3", and so on. See the
# "extruder" section above for a description of available parameters.
#[extruder1]
#step_pin: ar20
#dir_pin: ar21
#step_pin: ar36
#dir_pin: ar34
#...
# The heater_bed section describes a heated bed (if present - omit
# section if not present).
[heater_bed]
heater_pin: ar3
heater_pin: ar8
sensor_type: EPCOS 100K B57560G104F
sensor_pin: analog0
sensor_pin: analog14
control: watermark
#max_delta: 2.0
# On 'watermark' controlled heaters this is the number of degrees in
@ -242,7 +240,7 @@ max_temp: 110
# Print cooling fan (omit section if fan not present).
[fan]
pin: ar14
pin: ar9
# PWM output pin controlling the fan. This parameter must be
# provided.
#max_power: 1.0
@ -328,7 +326,7 @@ max_z_accel: 30
# whenever its associated heater is active.
#[heater_fan my_nozzle_fan]
# See the "fan" section for fan configuration parameters.
#pin: ar7
#pin: ar4
# The remaining variables are specific to heater_fan.
#heater: extruder
# Name of the config section defining the heater that this fan is