config: Add LDO Leviathan v1.2 generic config
Signed-off-by: Stefan Dej <meteyou@gmail.com>
This commit is contained in:
parent
0ccf5f8e47
commit
7ed3c679dc
|
@ -0,0 +1,241 @@
|
|||
# This file contains common pin mappings for the LDO Leviathan v1.2.
|
||||
|
||||
# To use this config, during "make menuconfig", select "Enable
|
||||
# low-level configuration options", select the STM32F446 micro-controller,
|
||||
# select a "32KiB bootloader", and select a "12Mhz crystal".
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
# HV-STEPPER-0
|
||||
[stepper_x]
|
||||
step_pin: PB10
|
||||
dir_pin: PB11
|
||||
enable_pin: !PG0
|
||||
microsteps: 32
|
||||
rotation_distance: 40
|
||||
endstop_pin: PC1 # X-ENDSTOP
|
||||
position_endstop: 0
|
||||
position_max: 200
|
||||
homing_speed: 50
|
||||
|
||||
[tmc5160 stepper_x]
|
||||
spi_bus: spi4
|
||||
cs_pin: PE15
|
||||
#diag0_pin: PG1
|
||||
interpolate: False
|
||||
sense_resistor: 0.075
|
||||
run_current: 0.8
|
||||
stealthchop_threshold: 0
|
||||
|
||||
# HV-STEPPER-1
|
||||
[stepper_y]
|
||||
step_pin: PF15
|
||||
dir_pin: PF14
|
||||
enable_pin: !PE9
|
||||
microsteps: 32
|
||||
rotation_distance: 40
|
||||
endstop_pin: PC2 # Y-ENDSTOP
|
||||
position_endstop: 0
|
||||
position_max: 200
|
||||
homing_speed: 50
|
||||
|
||||
[tmc5160 stepper_y]
|
||||
spi_bus: spi4
|
||||
cs_pin: PE11
|
||||
#diag0_pin: PE10
|
||||
interpolate: False
|
||||
sense_resistor: 0.075
|
||||
run_current: 0.8
|
||||
stealthchop_threshold: 0
|
||||
|
||||
# STEPPER-0
|
||||
[stepper_z]
|
||||
step_pin: PD4
|
||||
dir_pin: PD3
|
||||
enable_pin: !PD7
|
||||
microsteps: 32
|
||||
rotation_distance: 8
|
||||
endstop_pin: PC3 # Z-ENDSTOP
|
||||
position_endstop: 0
|
||||
position_max: 200
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PD5
|
||||
#diag_pin: PD6
|
||||
interpolate: False
|
||||
run_current: 0.6
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
# The Leviathan was developed for Voron printers. It therefore has several
|
||||
# steppers for the z-axes, but only one heater for one extruder.
|
||||
|
||||
# STEPPER-1
|
||||
#[stepper_z1]
|
||||
#step_pin: PC12
|
||||
#dir_pin: PC11
|
||||
#enable_pin: !PD2
|
||||
#microsteps: 32
|
||||
#rotation_distance: 8
|
||||
#
|
||||
#[tmc2209 stepper_z1]
|
||||
#uart_pin: PD5
|
||||
##diag_pin: PD6
|
||||
#interpolate: False
|
||||
#run_current: 0.6
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
# STEPPER-2
|
||||
#[stepper_z2]
|
||||
#step_pin: PC9
|
||||
#dir_pin: PC8
|
||||
#enable_pin: !PC10
|
||||
#microsteps: 32
|
||||
#rotation_distance: 8
|
||||
#
|
||||
#[tmc2209 stepper_z2]
|
||||
#uart_pin: PA8
|
||||
##diag_pin: PA15
|
||||
#interpolate: False
|
||||
#run_current: 0.6
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
# STEPPER-3
|
||||
#[stepper_z3]
|
||||
#step_pin: PG7
|
||||
#dir_pin: PG6
|
||||
#enable_pin: !PC7
|
||||
#microsteps: 32
|
||||
#rotation_distance: 8
|
||||
#
|
||||
#[tmc2209 stepper_z2]
|
||||
#uart_pin: PG8
|
||||
##diag_pin: PC6
|
||||
#interpolate: False
|
||||
#run_current: 0.6
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
# STEPPER-4
|
||||
[extruder]
|
||||
step_pin: PD10
|
||||
dir_pin: PD9
|
||||
enable_pin: !PD13
|
||||
microsteps: 32
|
||||
rotation_distance: 22.67
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PG10 # HEATER
|
||||
sensor_pin: PA2 # TH1
|
||||
sensor_type: ATC Semitec 104NT-4-R025H42G
|
||||
pullup_resistor: 2200
|
||||
control: pid
|
||||
pid_Kp: 36.787
|
||||
pid_Ki: 4.716
|
||||
pid_Kd: 71.735
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PD11
|
||||
#diag_pin: PD12
|
||||
interpolate: False
|
||||
run_current: 0.5
|
||||
stealthchop_threshold: 0
|
||||
|
||||
#[filament_switch_sensor material_0]
|
||||
#switch_pin: PC0 # FILAMENT-SENSOR
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PG11 # HEATBED
|
||||
sensor_pin: PA1 # TH0
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
pullup_resistor: 2200
|
||||
control: pid
|
||||
pid_kp: 56.723
|
||||
pid_ki: 5.561
|
||||
pid_kd: 144.642
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PB7 # FAN0
|
||||
#tachometer_pin: PB0
|
||||
|
||||
#[heater_fan fan1]
|
||||
#pin: PB3
|
||||
#tachometer_pin: PB4
|
||||
|
||||
#[heater_fan fan2]
|
||||
#pin: PF7
|
||||
#tachometer_pin: PF6
|
||||
|
||||
#[controller_fan fan3]
|
||||
#pin: PF9
|
||||
#tachometer_pin: PF8
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
||||
# CAN bus is also available on this board
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PG9, EXP1_2=PG12,
|
||||
EXP1_3=PG13, EXP1_4=PG14,
|
||||
EXP1_5=PC13, EXP1_6=PC14,
|
||||
EXP1_7=PC15, EXP1_8=PF0,
|
||||
EXP1_9=<GND>, EXP1_10=<5V>,
|
||||
|
||||
# EXP2 header
|
||||
EXP2_1=PA6, EXP2_2=PA5,
|
||||
EXP2_3=PE2, EXP2_4=PE4,
|
||||
EXP2_5=PE3, EXP2_6=PA7,
|
||||
EXP2_7=PE5, EXP2_8=<RST>,
|
||||
EXP2_9=<GND>, EXP2_10=PE4,
|
||||
|
||||
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
||||
|
||||
# EXTENSION PORT
|
||||
EXP3_1=<5V>, EXP3_2=<5V>, # max. 0.5A
|
||||
EXP3_3=<GND>, EXP3_4=<GND>,
|
||||
EXP3_5=<3.3V>, EXP3_6=<3.3V>, # max. 0.5A
|
||||
EXP3_7=PF5, EXP3_8=PF4,
|
||||
EXP3_9=PF3, EXP3_10=PF2,
|
||||
EXP3_11=PC4, EXP3_12=PC5, # EXP3_11 and EXP3_12 are ADC inputs
|
||||
EXP3_13=PB0, EXP3_14=PB1, # EXP3_13 and EXP3_14 are ADC inputs
|
||||
EXP3_15=PE8, EXP3_16=PE7, # EXP3_15 is UART5_TX, EXP3_16 is UART5_RX
|
||||
EXP3_17=PG5, EXP3_18=PG4,
|
||||
EXP3_19=PG3, EXP3_20=PG2,
|
||||
EXP3_21=PD15, EXP3_22=PD14,
|
||||
EXP3_23=PB15, EXP3_24=PB14, # EXP3_23 is SPI2_MOSI
|
||||
# EXP3_24 is SPI2_MISO
|
||||
EXP3_25=PB13, EXP3_26=PB12, # EXP3_25 is SPI2_SCK + CAN2_TX
|
||||
# EXP3_26 is SPI2_CS + CAN2_RX
|
||||
EXP3_27=<GND>, EXP3_28=<GND>,
|
||||
EXP3_29=<24V>, EXP3_30=<24V>, # max. 0.5A
|
||||
|
||||
#[probe]
|
||||
#sensor_pin: PF1 # Z-PROBE
|
||||
#z_offset: 0
|
||||
|
||||
#[led my_led]
|
||||
#white_pin: PE6 # LED-Strip
|
||||
|
||||
#[neopixel my_neopixel]
|
||||
#pin: PF10 # NEOPIXEL
|
||||
|
||||
#[temperature_sensor TH2]
|
||||
#sensor_type: ATC Semitec 104GT-2
|
||||
#sensor_pin: PA0 # TH2
|
||||
#pullup_resistor: 2200
|
||||
|
||||
#[temperature_sensor TH3]
|
||||
#sensor_type: ATC Semitec 104GT-2
|
||||
#sensor_pin: PA3 # TH3
|
||||
#pullup_resistor: 2200
|
|
@ -238,6 +238,7 @@ CONFIG ../../config/generic-bigtreetech-octopus-pro-v1.0.cfg
|
|||
CONFIG ../../config/generic-fysetc-s6.cfg
|
||||
CONFIG ../../config/generic-fysetc-s6-v2.cfg
|
||||
CONFIG ../../config/generic-fysetc-spider.cfg
|
||||
CONFIG ../../config/generic-ldo-leviathan-v1.2.cfg
|
||||
CONFIG ../../config/generic-mks-rumba32-v1.0.cfg
|
||||
CONFIG ../../config/printer-ratrig-v-minion-2021.cfg
|
||||
|
||||
|
|
Loading…
Reference in New Issue