config: Add generic config for Re-Arm (LPC1768)

Signed-off-by: Ax Smith-Laffin (ax@darknetweb.co.uk)

config/generic-re-arm.cfg

@@ -0,0 +1,100 @@
+# This file contains common pin mappings for Re-Arm. To use this
+# config, the firmware should be compiled for the LPC176x.
+
+# See the example.cfg file for a description of available parameters.
+
+[stepper_x]
+step_pin: P2.1
+dir_pin: P0.11
+enable_pin: !P0.10
+step_distance: .0125
+endstop_pin: ^P1.24
+#endstop_pin: ^P1.25
+position_endstop: 0.5
+position_min: 0
+position_max: 200
+homing_speed: 50
+
+# The stepper_y section is used to describe the Y axis as well as the
+# stepper controlling the X-Y movement.
+[stepper_y]
+step_pin: P2.2
+dir_pin: P0.20
+enable_pin: !P0.19
+step_distance: .0125
+endstop_pin: ^P1.26
+#endstop_pin: ^P1.27
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+[stepper_z]
+step_pin: P2.3
+dir_pin: P0.22
+enable_pin: !P0.21
+step_distance: .0025
+endstop_pin: ^P1.29
+#endstop_pin: ^P1.28
+position_endstop: 0.5
+position_min: 0
+position_max: 200
+
+[extruder]
+step_pin: P2.0
+dir_pin: P0.5
+enable_pin: !P0.4
+step_distance: .0011365 
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: P2.5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: P0.23
+control: pid
+pid_Kp: 22.2
+pid_Ki: 1.08
+pid_Kd: 114
+min_temp: 0
+max_temp: 250
+
+#[extruder1]
+#step_pin: P2.8
+#dir_pin: P2.13
+#enable_pin: !P4.29
+#heater_pin: P2.4
+#sensor_pin: P0.25
+#...
+
+[heater_bed]
+heater_pin: P2.7
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: P0.24
+control: watermark
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: P2.4
+
+[mcu]
+serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 5
+max_z_accel: 100
+
+
+# "RepRapDiscount 128x64 Full Graphic Smart Controller" type displays
+# Re-Arm will only work with this type of display
+#[display]
+#lcd_type: st7920
+#cs_pin: P0.16
+#sclk_pin: P0.15
+#sid_pin: P0.18
+#chip_delay needs to be set to the below for the LCD to initialise correctly.
+#chip_delay: .000040
+
+
+