config: Add Ender 3 S1 Plus (#5705)

Signed-off-by: Rob Casper <myallneedsemail@gmail.com>
This commit is contained in:
Fisheiyy 2022-09-16 11:06:49 -05:00 committed by GitHub
parent d9c917b950
commit 7527e57e5a
No known key found for this signature in database
GPG Key ID: 4AEE18F83AFDEB23
2 changed files with 132 additions and 0 deletions

View File

@ -0,0 +1,131 @@
# This file contains pin mappings for the stock 2022 Creality Ender 3
# S1 Plus. To use this config check the STM32 Chip on the Mainboard,
# during "make menuconfig" select accordingly either the
# STM32F103 with "28KiB bootloader" or the STM32F401 with
# "64KiB bootloader" and serial (on USART1 PA10/PA9) for both.
# For a direct serial connection, in "make menuconfig" select
# "Enable extra low-level configuration options" and Serial
# (on USART2 PA3/PA2), which is on the 10 pin IDC cable used
# for the LCD module as follows: 3: Tx, 4: Rx, 9: GND, 10: VCC
# Flash this firmware by copying "out/klipper.bin" to a SD card and
# turning on the printer with the card inserted. The filename
# must be changed to "firmware.bin"
# With STM32F401, you might need to put "firmware.bin" in a
# folder on the SD card called "STM32F4_UPDATE" in order to flash.
# See docs/Config_Reference.md for a description of parameters.
[stepper_x]
step_pin: PC2
dir_pin: PB9
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: !PA5
position_endstop: -10
position_max: 316
position_min: -15
homing_speed: 50
[stepper_y]
step_pin: PB8
dir_pin: PB7
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: !PA6
position_endstop: -10
position_max: 304
position_min: -15
homing_speed: 50
[stepper_z]
step_pin: PB6
dir_pin: !PB5
enable_pin: !PC3
microsteps: 16
rotation_distance: 8
endstop_pin: probe:z_virtual_endstop
position_max: 300
position_min: -4
[extruder]
step_pin: PB4
dir_pin: PB3
enable_pin: !PC3
microsteps: 16
gear_ratio: 42:12
rotation_distance: 26.359
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA1
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC5
control: pid
pid_Kp: 23.561
pid_Ki: 1.208
pid_Kd: 114.859
min_temp: 0
max_temp: 260
[heater_bed]
heater_pin: PA7
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC4
control: pid
pid_Kp: 71.867
pid_Ki: 1.536
pid_Kd: 840.843
min_temp: 0
max_temp: 100
[heater_fan hotend_fan]
pin: PC0
[fan]
pin: PA0
[mcu]
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
restart_method: command
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 2000
max_z_velocity: 5
max_z_accel: 100
[bltouch]
sensor_pin: ^PC14
control_pin: PC13
x_offset: -31.8
y_offset: -40.5
z_offset: 0
probe_with_touch_mode: true
stow_on_each_sample: false
[bed_mesh]
speed: 120
mesh_min: 20, 20
mesh_max: 283, 263
probe_count: 4,4
algorithm: bicubic
[safe_z_home]
home_xy_position: 187, 192
speed: 75
z_hop: 10
z_hop_speed: 5
move_to_previous: true
[filament_switch_sensor e0_sensor]
switch_pin: !PC15
pause_on_runout: true
runout_gcode: PAUSE
[pause_resume]
recover_velocity: 25

View File

@ -163,6 +163,7 @@ CONFIG ../../config/printer-creality-cr6se-2020.cfg
CONFIG ../../config/printer-creality-cr6se-2021.cfg
CONFIG ../../config/printer-creality-ender2pro-2021.cfg
CONFIG ../../config/printer-creality-ender3-s1-2021.cfg
CONFIG ../../config/printer-creality-ender3-s1plus-2022.cfg
CONFIG ../../config/printer-creality-ender3-v2-2020.cfg
CONFIG ../../config/printer-creality-ender3max-2021.cfg
CONFIG ../../config/printer-creality-ender3pro-2020.cfg