config: Add Sovol SV06 Plus (#6397)

New configuration for the Sovol SV06 Plus
Initial pass at adding a printer configuration for the Sovol SV06
Plus based on the existing Sovol SV06 config. Updated for the larger
build volume, added filament runout sensor, and removed any references
to the LCD screen since the stock screen doesn't work with Klipper.

Signed-off-by: Herb McNew <herb.mcnew@gmail.com>

config/printer-sovol-sv06-plus-2023.cfg

@@ -0,0 +1,147 @@
+# This file contains pin mappings for the stock Sovol SV06 Plus
+# To use this config, during "make menuconfig" select the
+# STM32F103 with a "28KiB bootloader" and serial (on USART1 PA10/PA9) communication.
+# Also, since it is using the GD32F103, please select Disable SWD at startup
+#
+# Flash this firmware by copying "out/klipper.bin" to a SD card and
+# turning on the printer with the card inserted. The firmware
+# filename must end in ".bin" and must not match the last filename
+# that was flashed.
+#
+# Note: The stock LCD display does not currently work with Klipper
+#
+# See docs/Config_Reference.md for a description of parameters.
+[mcu]
+serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
+restart_method: command
+
+[printer]
+kinematics: cartesian
+max_velocity: 500
+max_accel: 2000
+max_z_velocity: 10
+max_z_accel: 100
+
+[stepper_x]
+step_pin: PC2
+dir_pin: !PB9
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 40
+endstop_pin: tmc2209_stepper_x:virtual_endstop
+position_endstop: 0
+position_max: 305
+homing_speed: 40
+homing_retract_dist: 0
+
+[tmc2209 stepper_x]
+uart_pin: PC1
+run_current: 0.860
+sense_resistor: 0.150
+uart_address: 3
+driver_SGTHRS: 81
+diag_pin: PA5
+
+[stepper_y]
+step_pin: PB8
+dir_pin: PB7
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 40
+endstop_pin: tmc2209_stepper_y:virtual_endstop
+position_endstop: 0
+position_max: 305
+homing_speed: 40
+homing_retract_dist: 0
+
+[tmc2209 stepper_y]
+uart_pin: PC0
+run_current: 0.900
+sense_resistor: 0.150
+uart_address: 3
+driver_SGTHRS: 82
+diag_pin: PA6
+
+[stepper_z]
+step_pin: PB6
+dir_pin: !PB5
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 4
+endstop_pin: probe:z_virtual_endstop
+position_min: -4
+position_max: 350
+homing_speed: 4
+
+[tmc2209 stepper_z]
+uart_pin: PA15
+run_current: 1.000
+interpolate: False
+sense_resistor: 0.150
+uart_address: 3
+diag_pin: PA7
+
+[extruder]
+max_extrude_only_distance: 100.0
+step_pin: PB4
+dir_pin: !PB3
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 4.56
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PA1
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC5
+control: pid
+pid_kd: 41.96
+pid_kp: 15.66
+pid_ki: 1.49
+min_temp: 0
+max_temp: 300
+
+[tmc2209 extruder]
+uart_pin: PC14
+run_current: 0.550
+stealthchop_threshold: 0
+interpolate: False
+sense_resistor: 0.150
+uart_address: 3
+
+[heater_bed]
+heater_pin: PA2
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC4
+control: pid
+pid_kp: 186.38
+pid_ki: 36.12
+pid_kd: 637.30
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: PA0
+
+[probe]
+pin: PB1
+x_offset: 28
+y_offset: -20
+z_offset: 0
+
+[safe_z_home]
+home_xy_position: 123,170
+z_hop: 10
+z_hop_speed: 5
+
+[bed_mesh]
+speed: 120
+mesh_min: 28, 20
+mesh_max: 270, 270
+probe_count: 5
+algorithm: bicubic
+fade_end: 10
+fade_target: 0
+
+[filament_switch_sensor filament_runout_sensor]
+switch_pin: PA4
+pause_on_runout: True

test/klippy/printers.test

@@ -157,6 +157,7 @@ CONFIG ../../config/printer-anycubic-vyper-2021.cfg
 CONFIG ../../config/printer-monoprice-select-mini-v1-2016.cfg
 CONFIG ../../config/printer-sovol-sv05-2022.cfg
 CONFIG ../../config/printer-sovol-sv06-2022.cfg
+CONFIG ../../config/printer-sovol-sv06-plus-2023.cfg
 CONFIG ../../config/printer-sunlu-t3-2022.cfg
 
 # Printers using the stm32f103 via serial