From 743c766f47b2d276e019db740973bf1173ae3304 Mon Sep 17 00:00:00 2001 From: Spencer Owen Date: Thu, 17 Mar 2022 18:43:55 -0600 Subject: [PATCH] config: Adds Ender 2 Pro config (#5359) Adds a default config for Ender 2 Pro. Printer uses creality 4.2.3 board Signed-off-by: Spencer Owen --- config/printer-creality-ender2pro-2021.cfg | 106 +++++++++++++++++++++ test/klippy/printers.test | 1 + 2 files changed, 107 insertions(+) create mode 100644 config/printer-creality-ender2pro-2021.cfg diff --git a/config/printer-creality-ender2pro-2021.cfg b/config/printer-creality-ender2pro-2021.cfg new file mode 100644 index 00000000..3400890b --- /dev/null +++ b/config/printer-creality-ender2pro-2021.cfg @@ -0,0 +1,106 @@ +# This file contains pin mappings for the stock 2021 Creality +# Ender2 Pro. To use this config, during "make menuconfig" select +# the STM32F103 with a "28KiB bootloader" and serial +# (on USART1 PA10/PA9) communication. + +# If you prefer a direct serial connection, in "make menuconfig" +# select "Enable extra low-level configuration options" and select +# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC +# cable used for the LCD module as follows: +# 3: Tx, 4: Rx, 9: GND, 10: VCC + +# Flash this firmware by copying "out/klipper.bin" to a SD card and +# turning on the printer with the card inserted. The firmware +# filename must end in ".bin" and must not match the last filename +# that was flashed. + +# See docs/Config_Reference.md for a description of parameters. + +[stepper_x] +step_pin: PC2 +dir_pin: PB9 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 40 +endstop_pin: ^PA5 +position_min: -20 +position_endstop: -20 +position_max: 165 +homing_speed: 50 + +[stepper_y] +step_pin: PB8 +dir_pin: PB7 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 40 +endstop_pin: ^PA6 +position_min: -5 +position_endstop: -5 +position_max: 165 +homing_speed: 50 + +[stepper_z] +step_pin: PB6 +dir_pin: !PB5 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 8 +endstop_pin: ^PA7 +position_endstop: 0.0 +position_max: 180 + +[extruder] +max_extrude_only_distance: 100.0 +step_pin: PB4 +dir_pin: PB3 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 27.53480577 +nozzle_diameter: 0.400 +filament_diameter: 1.750 +heater_pin: PA1 +sensor_pin: PC5 +sensor_type: EPCOS 100K B57560G104F +control: pid +pid_Kp: 29.634 +pid_Ki: 2.102 +pid_Kd: 104.459 +min_temp: 0 +max_temp: 260 + +[heater_bed] +heater_pin: PB10 +sensor_type: EPCOS 100K B57560G104F +sensor_pin: PC4 +control: pid +pid_Kp: 72.921 +pid_Ki: 1.594 +pid_Kd: 834.031 +min_temp: 0 +max_temp: 80 + +[fan] +pin: PA0 + +[mcu] +serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0 +restart_method: command + +[printer] +kinematics: cartesian +max_velocity: 300 +max_accel: 3000 +max_z_velocity: 5 +max_z_accel: 100 + +[display] +lcd_type: st7920 +cs_pin: PB12 +sclk_pin: PB13 +sid_pin: PB15 +encoder_pins: ^PB14, ^PA2 +click_pin: ^!PB2 + +[output_pin beeper] +pin: PC6 diff --git a/test/klippy/printers.test b/test/klippy/printers.test index 4ab672b4..242321d9 100644 --- a/test/klippy/printers.test +++ b/test/klippy/printers.test @@ -157,6 +157,7 @@ CONFIG ../../config/printer-alfawise-u30-2018.cfg CONFIG ../../config/printer-creality-cr30-2021.cfg CONFIG ../../config/printer-creality-cr6se-2020.cfg CONFIG ../../config/printer-creality-cr6se-2021.cfg +CONFIG ../../config/printer-creality-ender2pro-2021.cfg CONFIG ../../config/printer-creality-ender3-v2-2020.cfg CONFIG ../../config/printer-creality-ender3max-2021.cfg CONFIG ../../config/printer-creality-ender3pro-2020.cfg