diff --git a/config/printer-tronxy-x8-2018.cfg b/config/printer-tronxy-x8-2018.cfg
new file mode 100644
index 00000000..b2cad58a
--- /dev/null
+++ b/config/printer-tronxy-x8-2018.cfg
@@ -0,0 +1,91 @@
+# This file contains the configurations and pin mappings for the
+# Tronxy X8 using the CXY-V2-0508 board.  To use this config file, the
+# firmware should be compiled for the AVR ATmega1284p, 16MHz.
+
+# Some Tronxy printers come without a bootloader present on the
+# board. In that case, use MCUDude MightyCore ATmega1284p bootloader
+# with TQFP44 Sanguino pinout. The package can be found at
+# (https://github.com/MCUdude/MightyCore).  Follow Klipper install
+# instructions but instead of "make flash FLASH_DEVICE=/dev/ttyACM0",
+# use the following command:
+# avrdude -p atmega1284p -c arduino -b 115200 -P /dev/ttyUSB0 -U out/klipper.elf.hex
+
+# See the example.cfg and example-extras.cfg files for a description
+# of available parameters.
+
+[mcu]
+serial: /dev/ttyUSB0
+
+[stepper_x]
+step_pin: PD7
+dir_pin: PC5
+enable_pin: !PD6
+step_distance: 0.010
+endstop_pin: ^!PC2
+position_endstop: -47
+position_max: 220
+position_min: -47
+homing_speed: 50
+
+[stepper_y]
+step_pin: PC6
+dir_pin: PC7
+enable_pin: !PD6
+step_distance: 0.010
+endstop_pin: ^!PC3
+position_endstop: 0
+position_max: 220
+position_min: 0
+homing_speed: 50
+
+[stepper_z]
+step_pin: PB3
+dir_pin: !PB2
+enable_pin: !PD6
+step_distance: 0.0025
+endstop_pin: ^!PC4
+position_endstop: 0
+position_max: 210
+homing_speed: 10
+
+[extruder]
+step_pin: PB1
+dir_pin: PB0
+enable_pin: !PD6
+step_distance: 0.009931
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PD5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PA7
+control: pid
+pid_Kp: 22.2
+pid_Ki: 1.08
+pid_Kd: 114
+min_temp: 0
+max_temp: 275
+
+[heater_bed]
+heater_pin: PD4
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PA6
+control: watermark
+max_delta: 2.0
+min_temp: 0
+max_temp: 150
+
+[fan]
+pin: PB4
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 1000
+max_z_velocity: 20
+max_z_accel: 100
+
+[display]
+lcd_type: st7920
+cs_pin: PA1
+sclk_pin: PC0
+sid_pin: PA3