config: Create printer-wanhao-duplicator-i3-plus-mark2-2019.cfg

Reported by @nzlrhyz.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

config/printer-wanhao-duplicator-i3-plus-mark2-2019.cfg

@@ -0,0 +1,81 @@
+# This file contains pin mappings for the Wanhao Duplicator i3 Plus
+# Mark II. To use this config, the firmware should be compiled for the
+# AVR atmega2560.
+
+# See the example.cfg file for a description of available parameters.
+
+[stepper_x]
+step_pin: PF7
+dir_pin: !PK0
+enable_pin: !PF6
+step_distance: .0125
+endstop_pin: ^!PF0
+position_endstop: 0
+position_max: 200
+homing_speed: 30.0
+
+[stepper_y]
+step_pin: PK2
+dir_pin: !PK3
+enable_pin: !PE4
+step_distance: .0125
+endstop_pin: ^!PA2
+position_endstop: 0
+position_max: 200
+homing_speed: 30.0
+
+[stepper_z]
+step_pin: PK5
+dir_pin: PK7
+enable_pin: !PK4
+step_distance: .0025
+endstop_pin: probe:z_virtual_endstop
+position_max: 180
+position_min: -0.5
+
+[extruder]
+step_pin: PF4
+dir_pin: PF5
+enable_pin: !PF3
+step_distance: 0.010417
+nozzle_diameter: 0.300
+filament_diameter: 1.750
+heater_pin: PG5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PF1
+control: pid
+pid_Kp: 20.982
+pid_Ki: 0.725
+pid_Kd: 151.861
+min_temp: 0
+max_temp: 260
+
+[heater_bed]
+heater_pin: PE5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PK6
+control: watermark
+min_temp: 0
+max_temp: 110
+
+[fan]
+pin: PE3
+
+[probe]
+pin: !PH3
+z_offset: 1.0
+
+[mcu]
+serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 800
+max_z_velocity: 5
+max_z_accel: 100
+
+[bed_mesh]
+min_point: 20,20
+max_point: 190,130
+probe_count: 4,4

test/klippy/printers.test

@@ -32,6 +32,7 @@ CONFIG ../../config/printer-seemecnc-rostock-max-v2-2015.cfg
 CONFIG ../../config/printer-tevo-flash-2018.cfg
 CONFIG ../../config/printer-velleman-k8200-2013.cfg
 CONFIG ../../config/printer-wanhao-duplicator-i3-plus-2017.cfg
+CONFIG ../../config/printer-wanhao-duplicator-i3-plus-mark2-2019.cfg
 CONFIG ../../config/printer-wanhao-duplicator-6-2016.cfg
 
 # Printers using the atmega1280