config: Add Anycubic Kobra Plus (#6084)
Signed-off-by: Derek Kaser <derek.kaser@gmail.com>
This commit is contained in:
parent
e3485fc31b
commit
5a69d0f857
|
@ -0,0 +1,197 @@
|
||||||
|
# This file contains a configuration for the Anycubic Kobra Plus printer.
|
||||||
|
#
|
||||||
|
# The Kobra Plus mainboard must be modified to correct conflicting UART
|
||||||
|
# addresses. As delivered, the X stepper and E0 stepper use UART address 0.
|
||||||
|
# To correct, move resistor R65 to R66. This moves the X stepper to address 3.
|
||||||
|
#
|
||||||
|
# After making this modification, any future firmwares will need to use the new
|
||||||
|
# address for the X stepper. To revert to the stock firmware, either undo the
|
||||||
|
# modification, or recompile the stock firmware using the correct addresses for
|
||||||
|
# X_SLAVE_ADDRESS and E0_SLAVE_ADDRESS.
|
||||||
|
#
|
||||||
|
# See docs/Config_Reference.md for a description of parameters.
|
||||||
|
#
|
||||||
|
# To build the firmware, use the following configuration:
|
||||||
|
# - Micro-controller: Huada Semiconductor HC32F460
|
||||||
|
# - Communication interface: Serial (PA3 & PA2) - Anycube
|
||||||
|
#
|
||||||
|
# Installation:
|
||||||
|
# 1. Rename the klipper bin to `firmware.bin` and copy it to an SD Card.
|
||||||
|
# 2. Power off the Printer, insert the SD Card and power it on.
|
||||||
|
# 3. The printer should beep several times and the LCD will be stuck on the
|
||||||
|
# Splash screen.
|
||||||
|
|
||||||
|
[mcu]
|
||||||
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||||||
|
restart_method: command
|
||||||
|
|
||||||
|
[printer]
|
||||||
|
kinematics: cartesian
|
||||||
|
max_velocity: 300
|
||||||
|
max_accel: 1800
|
||||||
|
max_z_velocity: 40
|
||||||
|
max_z_accel: 100
|
||||||
|
|
||||||
|
[stepper_x]
|
||||||
|
step_pin: PA5
|
||||||
|
dir_pin: PA4
|
||||||
|
enable_pin: !PC3
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 40
|
||||||
|
endstop_pin: !PA6
|
||||||
|
position_min: -4
|
||||||
|
position_endstop: -4
|
||||||
|
position_max: 304
|
||||||
|
homing_speed: 100
|
||||||
|
|
||||||
|
[tmc2209 stepper_x]
|
||||||
|
uart_pin: PA15
|
||||||
|
tx_pin: PA9
|
||||||
|
sense_resistor: 0.100
|
||||||
|
run_current: 0.9
|
||||||
|
uart_address: 3
|
||||||
|
stealthchop_threshold: 999999
|
||||||
|
|
||||||
|
[stepper_y]
|
||||||
|
step_pin: PC4
|
||||||
|
dir_pin: PA7
|
||||||
|
enable_pin: !PC3
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 32
|
||||||
|
endstop_pin: !PC5
|
||||||
|
position_min: -6
|
||||||
|
position_endstop: -6
|
||||||
|
position_max: 300
|
||||||
|
homing_speed: 100
|
||||||
|
|
||||||
|
[tmc2209 stepper_y]
|
||||||
|
uart_pin: PA15
|
||||||
|
tx_pin: PA9
|
||||||
|
sense_resistor: 0.100
|
||||||
|
run_current: 0.9
|
||||||
|
uart_address: 1
|
||||||
|
stealthchop_threshold: 999999
|
||||||
|
|
||||||
|
[stepper_z]
|
||||||
|
step_pin: PC7
|
||||||
|
dir_pin: !PC6
|
||||||
|
enable_pin: !PC3
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 8
|
||||||
|
endstop_pin: PA8
|
||||||
|
position_endstop: 0
|
||||||
|
position_min: -15
|
||||||
|
position_max: 350
|
||||||
|
homing_speed: 10
|
||||||
|
|
||||||
|
[tmc2209 stepper_z]
|
||||||
|
uart_pin: PA15
|
||||||
|
tx_pin: PA9
|
||||||
|
sense_resistor: 0.100
|
||||||
|
run_current: 0.9
|
||||||
|
uart_address: 2
|
||||||
|
stealthchop_threshold: 999999
|
||||||
|
|
||||||
|
[stepper_z1]
|
||||||
|
step_pin: PB1
|
||||||
|
dir_pin: !PB0
|
||||||
|
enable_pin: !PC3
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 8
|
||||||
|
|
||||||
|
[extruder]
|
||||||
|
max_extrude_only_distance: 200
|
||||||
|
max_extrude_only_velocity: 60
|
||||||
|
max_extrude_only_accel: 3000
|
||||||
|
step_pin: PC14
|
||||||
|
dir_pin: !PC15
|
||||||
|
enable_pin: !PC3
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 7.71
|
||||||
|
nozzle_diameter: 0.400
|
||||||
|
filament_diameter: 1.750
|
||||||
|
heater_pin: PA1
|
||||||
|
sensor_type: EPCOS 100K B57560G104F
|
||||||
|
sensor_pin: PC1
|
||||||
|
min_extrude_temp: 170
|
||||||
|
control: pid
|
||||||
|
pid_kp: 22.20
|
||||||
|
pid_ki: 1.08
|
||||||
|
pid_kd: 119.0
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 275
|
||||||
|
|
||||||
|
[tmc2208 extruder]
|
||||||
|
uart_pin: PA15
|
||||||
|
tx_pin: PA9
|
||||||
|
sense_resistor: 0.100
|
||||||
|
run_current: 0.8
|
||||||
|
uart_address: 0
|
||||||
|
stealthchop_threshold: 999999
|
||||||
|
|
||||||
|
[heater_bed]
|
||||||
|
heater_pin: PA0
|
||||||
|
sensor_type: EPCOS 100K B57560G104F
|
||||||
|
sensor_pin: PC0
|
||||||
|
control: pid
|
||||||
|
pid_kp: 97.1
|
||||||
|
pid_ki: 1.41
|
||||||
|
pid_kd: 1675.16
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 120
|
||||||
|
|
||||||
|
[filament_switch_sensor runout]
|
||||||
|
pause_on_runout: True
|
||||||
|
switch_pin: !PC13
|
||||||
|
|
||||||
|
[heater_fan controller_fan]
|
||||||
|
pin: PA14
|
||||||
|
heater: heater_bed
|
||||||
|
heater_temp: 45.0
|
||||||
|
|
||||||
|
[heater_fan hotend_fan]
|
||||||
|
pin: PA13
|
||||||
|
|
||||||
|
[fan]
|
||||||
|
pin: PB9
|
||||||
|
|
||||||
|
[probe]
|
||||||
|
pin: !PB6
|
||||||
|
speed: 2.0
|
||||||
|
lift_speed: 4.0
|
||||||
|
samples: 2
|
||||||
|
sample_retract_dist: 5
|
||||||
|
samples_tolerance_retries: 3
|
||||||
|
z_offset: 0.2
|
||||||
|
activate_gcode: probe_reset
|
||||||
|
|
||||||
|
[output_pin probe_reset_pin]
|
||||||
|
pin: PB7
|
||||||
|
value: 1
|
||||||
|
|
||||||
|
[safe_z_home]
|
||||||
|
home_xy_position: 0, 0
|
||||||
|
speed: 100
|
||||||
|
z_hop: 10
|
||||||
|
z_hop_speed: 15
|
||||||
|
move_to_previous: False
|
||||||
|
|
||||||
|
[bed_mesh]
|
||||||
|
speed: 100
|
||||||
|
mesh_min: 10, 10
|
||||||
|
mesh_max: 290, 290
|
||||||
|
algorithm: bicubic
|
||||||
|
probe_count: 5, 5
|
||||||
|
|
||||||
|
[gcode_macro probe_reset]
|
||||||
|
gcode:
|
||||||
|
SET_PIN PIN=probe_reset_pin VALUE=0
|
||||||
|
G4 P300
|
||||||
|
SET_PIN PIN=probe_reset_pin VALUE=1
|
||||||
|
G4 P100
|
||||||
|
|
||||||
|
[output_pin LED]
|
||||||
|
pin: PB8
|
||||||
|
|
||||||
|
[output_pin beeper]
|
||||||
|
pin: PB5
|
|
@ -0,0 +1,3 @@
|
||||||
|
# Base config file for boards using HC32F460
|
||||||
|
CONFIG_MACH_HC32F460=y
|
||||||
|
CONFIG_HC32F460_SERIAL_PA3_PA2=y
|
|
@ -250,6 +250,10 @@ CONFIG ../../config/generic-bigtreetech-skr-mini-e3-v3.0.cfg
|
||||||
DICTIONARY rp2040.dict
|
DICTIONARY rp2040.dict
|
||||||
CONFIG ../../config/generic-bigtreetech-skr-pico-v1.0.cfg
|
CONFIG ../../config/generic-bigtreetech-skr-pico-v1.0.cfg
|
||||||
|
|
||||||
|
# Anycubic Printers using trigorilla board with the hc32f460
|
||||||
|
DICTIONARY hc32f460-serial-PA3PA2.dict
|
||||||
|
CONFIG ../../config/printer-anycubic-kobra-plus-2022.cfg
|
||||||
|
|
||||||
# Printers using the PRU
|
# Printers using the PRU
|
||||||
DICTIONARY pru.dict host=linuxprocess.dict
|
DICTIONARY pru.dict host=linuxprocess.dict
|
||||||
CONFIG ../../config/generic-cramps.cfg
|
CONFIG ../../config/generic-cramps.cfg
|
||||||
|
|
Loading…
Reference in New Issue