config: Example config file for Creality CR5 Pro HT (#6089)
Signed-off-by: Brandon Baker <bakerbrandond@gmail.com>
This commit is contained in:
parent
4b1536d62f
commit
57c4da5ecf
|
@ -0,0 +1,152 @@
|
||||||
|
# This file contains common pin mappings for the Creality CR5 Pro HT.
|
||||||
|
# The mainboard is a Creality 3D v2.5.1 (8-bit mainboard with
|
||||||
|
# ATMega2560). To use this config, the firmware should be compiled for
|
||||||
|
# the AVR atmega2560.
|
||||||
|
|
||||||
|
# See docs/Config_Reference.md for a description of parameters.
|
||||||
|
[stepper_x]
|
||||||
|
step_pin: PF0 #ar54
|
||||||
|
dir_pin: !PF1 #ar55
|
||||||
|
enable_pin: !PD7 #!ar38
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 40 # 16 microsteps * 200 steps/rotation / 80 steps/mm
|
||||||
|
endstop_pin: ^!PE5 #^ar3
|
||||||
|
position_min: 0
|
||||||
|
position_max: 300
|
||||||
|
position_endstop: 0
|
||||||
|
homing_speed: 50
|
||||||
|
|
||||||
|
[stepper_y]
|
||||||
|
step_pin: PF6 #ar60
|
||||||
|
dir_pin: !PF7 #ar61
|
||||||
|
enable_pin: !PF2 #!ar56
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 40 # 16 microsteps * 200 steps/rotation / 80 steps/mm
|
||||||
|
endstop_pin: ^!PJ1 #^ar14
|
||||||
|
position_endstop: 0
|
||||||
|
position_max: 220
|
||||||
|
homing_speed: 50
|
||||||
|
|
||||||
|
[stepper_z]
|
||||||
|
step_pin: PL3 #ar46
|
||||||
|
dir_pin: !PL1 #!ar48
|
||||||
|
enable_pin: !PK0 #!ar62
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 4 # 16 microsteps * 200 steps/rotation / 800 steps/mm
|
||||||
|
position_max: 380
|
||||||
|
position_min: -10
|
||||||
|
endstop_pin: probe:z_virtual_endstop
|
||||||
|
|
||||||
|
[safe_z_home]
|
||||||
|
home_xy_position: 140, 110
|
||||||
|
speed: 80
|
||||||
|
z_hop: 10
|
||||||
|
z_hop_speed: 10
|
||||||
|
|
||||||
|
[extruder]
|
||||||
|
step_pin: PA4 # ar26
|
||||||
|
dir_pin: !PA6 # !ar28
|
||||||
|
enable_pin: !PA2 # !ar24
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 23.24736 # 16 microsteps * 200 steps/rotation / 137.65 steps/mm
|
||||||
|
nozzle_diameter: 0.400
|
||||||
|
filament_diameter: 1.750
|
||||||
|
heater_pin: PB4 #ar10
|
||||||
|
sensor_type: EPCOS 100K B57560G104F
|
||||||
|
sensor_pin: PK5 #analog13
|
||||||
|
control: pid
|
||||||
|
pid_kp: 17.647
|
||||||
|
pid_ki: 1.079
|
||||||
|
pid_kd: 72.131
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 300
|
||||||
|
|
||||||
|
[heater_bed]
|
||||||
|
heater_pin: PH5 #ar8
|
||||||
|
sensor_type: ATC Semitec 104GT-2
|
||||||
|
sensor_pin: PK6 #analog14
|
||||||
|
control: pid
|
||||||
|
pid_kp: 75.501
|
||||||
|
pid_ki: 2.542
|
||||||
|
pid_kd: 560.598
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 130
|
||||||
|
|
||||||
|
[fan]
|
||||||
|
pin: PH6 #ar9
|
||||||
|
|
||||||
|
[mcu]
|
||||||
|
serial: /dev/ttyUSB0
|
||||||
|
restart_method: command
|
||||||
|
|
||||||
|
[printer]
|
||||||
|
kinematics: cartesian
|
||||||
|
max_velocity: 300
|
||||||
|
max_accel: 2000
|
||||||
|
max_z_velocity: 5
|
||||||
|
max_z_accel: 100
|
||||||
|
|
||||||
|
#[display]
|
||||||
|
# DWIN screen currently unsupported
|
||||||
|
|
||||||
|
[bltouch]
|
||||||
|
sensor_pin: ^PD2 #^ar19
|
||||||
|
control_pin: PB5 #ar11
|
||||||
|
set_output_mode: 5V
|
||||||
|
pin_move_time: 0.4
|
||||||
|
x_offset: 37.0
|
||||||
|
y_offset: 0.0
|
||||||
|
z_offset: 2.40
|
||||||
|
samples: 2
|
||||||
|
sample_retract_dist: 2
|
||||||
|
samples_result: average
|
||||||
|
|
||||||
|
[bed_mesh]
|
||||||
|
speed: 50
|
||||||
|
horizontal_move_z: 6
|
||||||
|
mesh_min: 47,10
|
||||||
|
mesh_max: 270,210
|
||||||
|
probe_count: 7,7
|
||||||
|
algorithm: bicubic
|
||||||
|
|
||||||
|
[pause_resume]
|
||||||
|
recover_velocity: 50
|
||||||
|
|
||||||
|
[filament_switch_sensor fil_runout_sensor]
|
||||||
|
pause_on_runout: True
|
||||||
|
switch_pin: !PE4 #ar2
|
||||||
|
|
||||||
|
[bed_screws]
|
||||||
|
screw1: 8,5
|
||||||
|
screw1_name: front left screw
|
||||||
|
screw2: 8,210
|
||||||
|
screw2_name: rear left screw
|
||||||
|
screw3: 218,210
|
||||||
|
screw3_name: rear right screw
|
||||||
|
screw4: 218,5
|
||||||
|
screw4_name: front right screw
|
||||||
|
|
||||||
|
[screws_tilt_adjust]
|
||||||
|
screw1: 8,5
|
||||||
|
screw1_name: front left screw
|
||||||
|
screw2: 8,210
|
||||||
|
screw2_name: rear left screw
|
||||||
|
screw3: 218,210
|
||||||
|
screw3_name: rear right screw
|
||||||
|
screw4: 218,5
|
||||||
|
screw4_name: front right screw
|
||||||
|
speed: 50
|
||||||
|
horizontal_move_z: 10
|
||||||
|
screw_thread: CW-M4
|
||||||
|
|
||||||
|
[output_pin case_light]
|
||||||
|
pin: PH4 #ar7
|
||||||
|
value: 1
|
||||||
|
|
||||||
|
[gcode_macro CASE_LIGHT_ON]
|
||||||
|
gcode:
|
||||||
|
SET_PIN PIN=case_light VALUE=1
|
||||||
|
|
||||||
|
[gcode_macro CASE_LIGHT_OFF]
|
||||||
|
gcode:
|
||||||
|
SET_PIN PIN=case_light VALUE=0
|
|
@ -31,6 +31,7 @@ CONFIG ../../config/printer-anycubic-i3-mega-2017.cfg
|
||||||
CONFIG ../../config/printer-anycubic-kossel-2016.cfg
|
CONFIG ../../config/printer-anycubic-kossel-2016.cfg
|
||||||
CONFIG ../../config/printer-anycubic-kossel-plus-2017.cfg
|
CONFIG ../../config/printer-anycubic-kossel-plus-2017.cfg
|
||||||
CONFIG ../../config/printer-bq-hephestos-2014.cfg
|
CONFIG ../../config/printer-bq-hephestos-2014.cfg
|
||||||
|
CONFIG ../../config/printer-creality-cr5pro-ht-2022.cfg
|
||||||
CONFIG ../../config/printer-creality-cr10-v3-2020.cfg
|
CONFIG ../../config/printer-creality-cr10-v3-2020.cfg
|
||||||
CONFIG ../../config/printer-creality-cr10s-2017.cfg
|
CONFIG ../../config/printer-creality-cr10s-2017.cfg
|
||||||
CONFIG ../../config/printer-creality-cr20-2018.cfg
|
CONFIG ../../config/printer-creality-cr20-2018.cfg
|
||||||
|
|
Loading…
Reference in New Issue