config: Add Creality CR-30 PrintMill support
Add support for the Creality CR-30 'PrintMill', and its base board, the Creality v4.2.10. Add them to the `test/klippy/printers.test` test suite Signed-off-by: Jason S. McMullan <jason.mcmullan@gmail.com>
This commit is contained in:
Jason S. McMullan
KevinOConnor
parent
45cd3543e3
commit
44387568f3
|
|
@ -0,0 +1,144 @@
|
|||
# This file contains pin mappings for the Creality "v4.2.10" board. To
|
||||
# use this config, during "make menuconfig" select the STM32F103 with
|
||||
# a "28KiB bootloader" and serial (on USART1 PA10/PA9) communication.
|
||||
|
||||
# Flash this firmware by copying "out/klipper.bin" to a SD card and
|
||||
# If you prefer a direct serial connection, in "make menuconfig"
|
||||
# select "Enable extra low-level configuration options" and select
|
||||
# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC
|
||||
# cable used for the LCD module as follows:
|
||||
# 3: Tx, 4: Rx, 9: GND, 10: VCC
|
||||
|
||||
# turning on the printer with the card inserted. The firmware
|
||||
# filename must end in ".bin" and must not match the last filename
|
||||
# that was flashed.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PC2
|
||||
dir_pin: !PB9
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^!PA3
|
||||
position_endstop: 0
|
||||
position_max: 220
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PB8
|
||||
dir_pin: !PB7
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^!PA7
|
||||
position_endstop: 0
|
||||
position_max: 240
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB6
|
||||
dir_pin: !PB5
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 2.75
|
||||
endstop_pin: ^!PA5
|
||||
position_endstop: 0.0
|
||||
position_max: 200
|
||||
|
||||
[extruder]
|
||||
step_pin: PB4
|
||||
dir_pin: !PB3
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 23.0
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PA0
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC5
|
||||
control: pid
|
||||
pid_Kp: 21.527
|
||||
pid_Ki: 1.063
|
||||
pid_Kd: 108.982
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
# K-FAN1
|
||||
[fan]
|
||||
pin: PA2
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PA1
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC4
|
||||
control: pid
|
||||
pid_Kp: 54.027
|
||||
pid_Ki: 0.770
|
||||
pid_Kd: 948.182
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||||
baud: 250000
|
||||
restart_method: command
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 200
|
||||
max_accel: 1500
|
||||
max_z_velocity: 20
|
||||
max_z_accel: 500
|
||||
|
||||
# [filament_switch_sensor spool]
|
||||
# pause_on_runout: True
|
||||
# switch_pin: ^!PA6
|
||||
|
||||
# K-FAN2
|
||||
# [fan_generic k_fan2]
|
||||
# pin: PC0
|
||||
|
||||
# K-FAN3
|
||||
# [fan_generic k_fan3]
|
||||
# pin: PC1
|
||||
|
||||
# [temperature_sensor mcu_temp]
|
||||
# sensor_type: temperature_mcu
|
||||
# min_temp: 0
|
||||
# max_temp: 100
|
||||
|
||||
|
||||
# Neopixel LED support
|
||||
# [neopixel led_neopixel]
|
||||
# pin: PC14
|
||||
|
||||
# BL-touch
|
||||
# [bltouch]
|
||||
# control_pin: PB0
|
||||
# sensor_pin: PB1
|
||||
|
||||
# TMC Uart Mod Pins:
|
||||
# https://github.com/adelyser/Marlin-CR30/wiki
|
||||
# [tmc2208 stepper_x]
|
||||
# uart_pin: PB0
|
||||
#
|
||||
# [tmc2208 stepper_y]
|
||||
# uart_pin: PB1
|
||||
#
|
||||
# [tmc2208 stepper_z]
|
||||
# uart_pin: PA13
|
||||
#
|
||||
# [tmc2208 extruder]
|
||||
# uart_pin: PA14
|
||||
|
||||
# [display]
|
||||
# lcd_type: st7920
|
||||
# cs_pin: PB12
|
||||
# sclk_pin: PB13
|
||||
# sid_pin: PB15
|
||||
# encoder_pins: ^PB14, ^PB10
|
||||
# click_pin: ^!PB2
|
||||
|
||||
# [output_pin beeper]
|
||||
# pin: PC6
|
||||
|
|
@ -0,0 +1,167 @@
|
|||
# This file contains pin mappings for the Creality CR-30 PrintMill. To
|
||||
# use this config, during "make menuconfig" select the STM32F103 with
|
||||
# a "28KiB bootloader" and serial (on USART1 PA10/PA9) communication.
|
||||
|
||||
# If you prefer a direct serial connection, in "make menuconfig"
|
||||
# select "Enable extra low-level configuration options" and select
|
||||
# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC
|
||||
# cable used for the LCD module as follows:
|
||||
# 3: Tx, 4: Rx, 9: GND, 10: VCC
|
||||
|
||||
# Flash this firmware by copying "out/klipper.bin" to a SD card and
|
||||
# turning on the printer with the card inserted. The firmware
|
||||
# filename must end in ".bin" and must not match the last filename
|
||||
# that was flashed.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PC2
|
||||
dir_pin: !PB9
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^!PA3
|
||||
position_endstop: 0
|
||||
position_max: 220
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PB8
|
||||
dir_pin: !PB7
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^!PA7
|
||||
position_endstop: 0
|
||||
position_max: 240
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB6
|
||||
dir_pin: !PB5
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 2.75
|
||||
endstop_pin: ^!PA5
|
||||
position_endstop: 0.0
|
||||
position_max: 20000000
|
||||
|
||||
[extruder]
|
||||
step_pin: PB4
|
||||
dir_pin: !PB3
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 23.0
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PA0
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC5
|
||||
control: pid
|
||||
pid_Kp: 21.527
|
||||
pid_Ki: 1.063
|
||||
pid_Kd: 108.982
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
[filament_switch_sensor spool]
|
||||
pause_on_runout: True
|
||||
switch_pin: ^!PA6
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PA1
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC4
|
||||
control: pid
|
||||
pid_Kp: 54.027
|
||||
pid_Ki: 0.770
|
||||
pid_Kd: 948.182
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
# K-FAN1
|
||||
[fan]
|
||||
pin: PA2
|
||||
|
||||
# K-FAN2
|
||||
[fan_generic k_fan2]
|
||||
pin: PC0
|
||||
|
||||
# K-FAN3
|
||||
[fan_generic k_fan3]
|
||||
pin: PC1
|
||||
|
||||
[temperature_sensor mcu_temp]
|
||||
sensor_type: temperature_mcu
|
||||
min_temp: 0
|
||||
max_temp: 100
|
||||
|
||||
[output_pin led]
|
||||
pin: PC14
|
||||
static_value: 0
|
||||
|
||||
# Neopixel LED support
|
||||
# [neopixel led_neopixel]
|
||||
# pin: PC14
|
||||
|
||||
# BL-touch
|
||||
# [bltouch]
|
||||
# control_pin: PB0
|
||||
# sensor_pin: PB1
|
||||
|
||||
# TMC Uart Mod Pins:
|
||||
# https://github.com/adelyser/Marlin-CR30/wiki
|
||||
# [tmc2208 stepper_x]
|
||||
# uart_pin: PB0
|
||||
#
|
||||
# [tmc2208 stepper_y]
|
||||
# uart_pin: PB1
|
||||
#
|
||||
# [tmc2208 stepper_z]
|
||||
# uart_pin: PA13
|
||||
#
|
||||
# [tmc2208 extruder]
|
||||
# uart_pin: PA14
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||||
baud: 250000
|
||||
restart_method: command
|
||||
|
||||
[display]
|
||||
lcd_type: st7920
|
||||
cs_pin: PB12
|
||||
sclk_pin: PB13
|
||||
sid_pin: PB15
|
||||
encoder_pins: ^PB14, ^PB10
|
||||
click_pin: ^!PB2
|
||||
|
||||
[output_pin beeper]
|
||||
pin: PC6
|
||||
|
||||
[printer]
|
||||
kinematics: corexy
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
# Override to support unlimited belt size
|
||||
# (homing Z simply resets its virtual position to 0.0)
|
||||
[homing_override]
|
||||
axes: z
|
||||
set_position_z: 0
|
||||
gcode:
|
||||
{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}G28 X0 Y0{% endif %}
|
||||
{% if params.X is defined %}G28 X0{% endif %}
|
||||
{% if params.Y is defined %}G28 Y0{% endif %}
|
||||
G92 Z0
|
||||
|
||||
# Eject all printed parts from the belt
|
||||
[gcode_macro BED_EJECT]
|
||||
gcode:
|
||||
TURN_OFF_HEATERS
|
||||
G28 ; Re-home
|
||||
G1 X50 Y50 ; Move hotend out of the way of the belt
|
||||
G1 Z420 F4000 ; Unload belt
|
||||
G28 Z0 ; Re-home Z
|
||||
|
|
@ -133,12 +133,14 @@ CONFIG ../../config/generic-bigtreetech-skr-e3-dip.cfg
|
|||
# Printers using the stm32f103 via serial
|
||||
DICTIONARY stm32f103-serial.dict
|
||||
CONFIG ../../config/generic-creality-v4.2.7.cfg
|
||||
CONFIG ../../config/generic-creality-v4.2.10.cfg
|
||||
CONFIG ../../config/generic-fysetc-cheetah-v1.1.cfg
|
||||
CONFIG ../../config/generic-fysetc-cheetah-v1.2.cfg
|
||||
CONFIG ../../config/generic-mks-robin-e3.cfg
|
||||
CONFIG ../../config/generic-mks-robin-nano-v1.cfg
|
||||
CONFIG ../../config/generic-mks-robin-nano-v2.cfg
|
||||
CONFIG ../../config/printer-alfawise-u30-2018.cfg
|
||||
CONFIG ../../config/printer-creality-cr30-2021.cfg
|
||||
CONFIG ../../config/printer-creality-cr6se-2020.cfg
|
||||
CONFIG ../../config/printer-creality-cr6se-2021.cfg
|
||||
CONFIG ../../config/printer-creality-ender3-v2-2020.cfg
|
||||
|
|
|
|||
Loading…
Reference in New Issue