config: fixes in anycubic delta plus default config file (#2176)

Signed-off-by: Jakub Kruszona-Zawadzki <acid@moosefs.com>
This commit is contained in:
Jakub Kruszona-Zawadzki 2019-12-02 00:51:46 +01:00 committed by KevinOConnor
parent 43bb45a1d3
commit 41dd53f62c
1 changed files with 21 additions and 20 deletions

View File

@ -19,7 +19,7 @@ homing_speed: 60
# and meassure the distance from nozzle to bed. # and meassure the distance from nozzle to bed.
# This value then needs to be added. # This value then needs to be added.
position_endstop: 295.6 position_endstop: 295.6
arm_length: 271.50 arm_length: 269.0
[stepper_b] [stepper_b]
step_pin: ar60 step_pin: ar60
@ -39,7 +39,7 @@ endstop_pin: ^ar19
step_pin: ar26 step_pin: ar26
dir_pin: !ar28 dir_pin: !ar28
enable_pin: !ar24 enable_pin: !ar24
step_distance: 0.010989 step_distance: 0.0104166
nozzle_diameter: 0.400 nozzle_diameter: 0.400
filament_diameter: 1.750 filament_diameter: 1.750
heater_pin: ar10 heater_pin: ar10
@ -53,13 +53,16 @@ min_extrude_temp: 150
min_temp: 0 min_temp: 0
max_temp: 275 max_temp: 275
#[heater_bed] [heater_bed]
#heater_pin: ar8 heater_pin: ar8
#sensor_type: EPCOS 100K B57560G104F sensor_type: EPCOS 100K B57560G104F
#sensor_pin: analog14 sensor_pin: analog14
#control: watermark control: pid
#min_temp: 0 pid_kp: 73.517
#max_temp: 130 pid_ki: 1.132
pid_kd: 1193.728
min_temp: 0
max_temp: 130
[fan] [fan]
pin: ar9 pin: ar9
@ -68,6 +71,12 @@ kick_start_time: 0.200
[heater_fan extruder_cooler_fan] [heater_fan extruder_cooler_fan]
pin: ar44 pin: ar44
# if you want to use your probe for DELTA_CALIBRATE you will need that
#[probe]
#pin: ^ar18
#z_offset: 15.9
#samples: 3
[mcu] [mcu]
serial: /dev/ttyUSB0 serial: /dev/ttyUSB0
pin_map: arduino pin_map: arduino
@ -77,23 +86,15 @@ kinematics: delta
max_velocity: 500 max_velocity: 500
max_accel: 3000 max_accel: 3000
max_z_velocity: 200 max_z_velocity: 200
delta_radius: 115 delta_radius: 134.4
# if you want to DELTA_CALIBRATE you may need that # if you want to DELTA_CALIBRATE you may need that
#minimum_z_position: -5 #minimum_z_position: -5
[idle_timeout] [idle_timeout]
timeout: 360 timeout: 360
#[delta_calibrate] [delta_calibrate]
#radius: 115 radius: 115
#manual_probe:
# If true, then DELTA_CALIBRATE will perform manual probing. If
# false, then a PROBE command will be run at each probe
# point. Manual probing is accomplished by manually jogging the Z
# position of the print head at each probe point and then issuing a
# NEXT extended g-code command to record the position at that
# point. The default is false if a [probe] config section is present
# and true otherwise.
# "RepRapDiscount 2004 Smart Controller" type displays # "RepRapDiscount 2004 Smart Controller" type displays
[display] [display]