diff --git a/config/printer-anet-a8-2019.cfg b/config/printer-anet-a8-2019.cfg
new file mode 100644
index 00000000..b72dc885
--- /dev/null
+++ b/config/printer-anet-a8-2019.cfg
@@ -0,0 +1,92 @@
+# This file contains common pin mappings for Anet A8 Plus printer from 2019.
+# To use this config, the firmware should be compiled for
+# the AVR atmega1284p.
+
+# Note that the "make flash" command does not work with Anet boards -
+# the boards are typically flashed with this command:
+# avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[stepper_x]
+step_pin: PD7
+dir_pin: !PC5
+enable_pin: !PD6
+microsteps: 16
+rotation_distance: 32
+endstop_pin: ^!PC2
+position_endstop: -30
+position_max: 300
+position_min: -30
+homing_speed: 50
+
+[stepper_y]
+step_pin: PC6
+dir_pin: !PC7
+enable_pin: !PD6
+microsteps: 16
+rotation_distance: 32
+endstop_pin: ^!PC3
+position_endstop: -8
+position_max: 300
+position_min: -8
+homing_speed: 50
+
+[stepper_z]
+step_pin: PB3
+dir_pin: !PB2
+enable_pin: !PA5
+microsteps: 16
+rotation_distance: 8
+endstop_pin: ^!PC4
+position_endstop: 0.5
+position_max: 350
+position_min: 0.5
+homing_speed: 20
+
+[extruder]
+step_pin: PB1
+dir_pin: PB0
+enable_pin: !PD6
+microsteps: 16
+rotation_distance: 33.600
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PD5
+sensor_type: Generic 3950
+sensor_pin: PA7
+control: pid
+pid_Kp: 2.151492
+pid_Ki: 0.633897
+pid_Kd: 230.042965
+min_temp: 0
+max_temp: 250
+
+[heater_bed]
+heater_pin: PD4
+sensor_type: Generic 3950
+sensor_pin: PA6
+control: watermark
+min_temp: 0
+max_temp: 100
+
+[fan]
+pin: PB4
+
+[mcu]
+serial: /dev/ttyUSB0
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 1000
+max_z_velocity: 20
+max_z_accel: 100
+
+[display]
+lcd_type: st7920
+cs_pin: PA4
+sclk_pin: PA1
+sid_pin: PA3
+encoder_pins: ^PD2, ^PD3
+click_pin: ^!PC0
diff --git a/test/klippy/printers.test b/test/klippy/printers.test
index c65b8f52..243a95a1 100644
--- a/test/klippy/printers.test
+++ b/test/klippy/printers.test
@@ -71,6 +71,7 @@ DICTIONARY atmega1284p.dict
 CONFIG ../../config/generic-melzi.cfg
 CONFIG ../../config/printer-anet-a4-2018.cfg
 CONFIG ../../config/printer-anet-a8-2017.cfg
+CONFIG ../../config/printer-anet-a8-2019.cfg
 CONFIG ../../config/printer-anet-e10-2018.cfg
 CONFIG ../../config/printer-anet-e16-2019.cfg
 CONFIG ../../config/printer-creality-cr10-2017.cfg