config: Added Config for Creality Ender 5 Pro 2020 (#4836)

Signed-off-by:  Maxim Schessler <maxim.schessler@gmail.com>
This commit is contained in:
SyrasX 2022-03-19 01:42:15 +01:00 committed by GitHub
parent 1390b4d600
commit 3e0c0e9ccf
No known key found for this signature in database
GPG Key ID: 4AEE18F83AFDEB23
2 changed files with 102 additions and 0 deletions

View File

@ -0,0 +1,101 @@
# This file contains pin mappings for the stock 2020 Creality Ender 5
# Pro with the 32-bit Creality 4.2.2 board. To use this config, during
# "make menuconfig" select the STM32F103 with a "28KiB bootloader" and
# with "Use USB for communication" disabled.
# If you prefer a direct serial connection, in "make menuconfig"
# select "Enable extra low-level configuration options" and select the
# USART3 serial port, which is broken out on the 10 pin IDC cable used
# for the LCD module as follows:
# 3: Tx, 4: Rx, 9: GND, 10: VCC
# Flash this firmware by copying "out/klipper.bin" to a SD card and
# turning on the printer with the card inserted. The firmware
# filename must end in ".bin" and must not match the last filename
# that was flashed.
# See docs/Config_Reference.md for a description of parameters.
[stepper_x]
step_pin: PC2
dir_pin: PB9
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: ^PA5
position_endstop: 220
position_max: 220
homing_speed: 50
[stepper_y]
step_pin: PB8
dir_pin: PB7
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: ^PA6
position_endstop: 220
position_max: 220
homing_speed: 50
[stepper_z]
step_pin: PB6
dir_pin: PB5
enable_pin: !PC3
microsteps: 16
rotation_distance: 4
endstop_pin: ^PA7
position_max: 300
position_endstop: 0.0
[extruder]
max_extrude_only_distance: 100.0
step_pin: PB4
dir_pin: PB3
enable_pin: !PC3
microsteps: 16
rotation_distance: 32.342
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA1
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC5
control: pid
pid_kp: 24.831
pid_ki: 1.346
pid_kd: 114.532
min_temp: 0
max_temp: 260
[heater_bed]
heater_pin: PA2
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC4
control: pid
pid_kp: 66.429
pid_ki: 1.197
pid_kd: 921.707
min_temp: 0
max_temp: 135
[fan]
pin: PA0
[mcu]
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
restart_method: command
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
[display]
lcd_type: st7920
cs_pin: PB12
sclk_pin: PB13
sid_pin: PB15
encoder_pins: ^PB14, ^PB10
click_pin: ^!PB2

View File

@ -161,6 +161,7 @@ CONFIG ../../config/printer-creality-ender2pro-2021.cfg
CONFIG ../../config/printer-creality-ender3-v2-2020.cfg CONFIG ../../config/printer-creality-ender3-v2-2020.cfg
CONFIG ../../config/printer-creality-ender3max-2021.cfg CONFIG ../../config/printer-creality-ender3max-2021.cfg
CONFIG ../../config/printer-creality-ender3pro-2020.cfg CONFIG ../../config/printer-creality-ender3pro-2020.cfg
CONFIG ../../config/printer-creality-ender5pro-2020.cfg
CONFIG ../../config/printer-creality-ender6-2020.cfg CONFIG ../../config/printer-creality-ender6-2020.cfg
CONFIG ../../config/printer-creality-sermoonD1-2021.cfg CONFIG ../../config/printer-creality-sermoonD1-2021.cfg
CONFIG ../../config/printer-elegoo-neptune2-2021.cfg CONFIG ../../config/printer-elegoo-neptune2-2021.cfg