3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

config: Minor rearrangement of example-extras.cfg 

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
Kevin O'Connor 2019-03-22 20:44:11 -04:00
parent efab177645
commit 3945905420
1 changed files with 34 additions and 28 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

62
config/example-extras.cfg
View File

@ -7,16 +7,6 @@
# section defining the pins must be listed in the config file before # section defining the pins must be listed in the config file before
# any sections using those pins. # any sections using those pins.
# TSLl401CL Based Filament Width Sensor
#[tsl1401cl_filament_width_sensor]
#pin: analog5
#default_nominal_filament_diameter: 1.75 # (mm)
# Maximum allowed filament diameter difference as mm
#max_difference: 0.2
# The distance from sensor to the melting chamber as mm
#measurement_delay 100
# Z height probe. One may define this section to enable Z height # Z height probe. One may define this section to enable Z height
# probing hardware. When this section is enabled, PROBE and # probing hardware. When this section is enabled, PROBE and
@ -1379,10 +1369,6 @@
# the command invoking the macro. # the command invoking the macro.
# Replicape support - see the generic-replicape.cfg file for further
# details.
#[replicape]
# Enable the "M118" and "RESPOND" extended commands. # Enable the "M118" and "RESPOND" extended commands.
# [respond] # [respond]
# default_type: echo # default_type: echo
@ -1395,6 +1381,7 @@
# Directly sets the default prefix. If present, this value will override # Directly sets the default prefix. If present, this value will override
# the "default_type". # the "default_type".
# The heater_generic section is used to describe a custom/generic heater. # The heater_generic section is used to describe a custom/generic heater.
# These behave the same as typical heaters (extruders, heated beds) and # These behave the same as typical heaters (extruders, heated beds) and
# can be configured as similarly. # can be configured as similarly.
@ -1423,6 +1410,7 @@
# See the heater section in example.cfg for the definition of the # See the heater section in example.cfg for the definition of the
# above parameters. # above parameters.
# Temperature sensors. One can define any number of temperature # Temperature sensors. One can define any number of temperature
# sensors. Their values are reported via the M105 command. # sensors. Their values are reported via the M105 command.
#[temperature_sensor my_sensor] #[temperature_sensor my_sensor]
@ -1440,26 +1428,44 @@
# Pause/Resume functionality with support of position capture and restore # Pause/Resume functionality with support of position capture and restore
#[pause_resume] #[pause_resume]
#recover_velocity: 50. #recover_velocity: 50.
# When capture/restore is enabled, the speed at which to return to # When capture/restore is enabled, the speed at which to return to
# the captured position (in mm/s). Default is 50.0 mm/s. # the captured position (in mm/s). Default is 50.0 mm/s.
# Filament Switch Sensor. Support for filament insert and runout detection # Filament Switch Sensor. Support for filament insert and runout detection
# using a switch sensor, such as an endstop switch. # using a switch sensor, such as an endstop switch.
#[filament_switch_sensor my_sensor] #[filament_switch_sensor my_sensor]
#pause_on_runout: True #pause_on_runout: True
# When set to True, a PAUSE will execute immediately after a runout is # When set to True, a PAUSE will execute immediately after a runout
# detected. Note that if pause_on_runout is False and the runout_gcode is # is detected. Note that if pause_on_runout is False and the
# omitted then runout detection is disabled. Default is True. # runout_gcode is omitted then runout detection is disabled. Default
# is True.
#runout_gcode: #runout_gcode:
# The gcode to run after a filament runout is detected. If pause_on_runout # The gcode to run after a filament runout is detected. If
# is set to True this gcode will run after the PAUSE is complete. The default # pause_on_runout is set to True this gcode will run after the PAUSE
# is not to run any gcode commands. # is complete. The default is not to run any gcode commands.
#insert_gcode: #insert_gcode:
# The gcode to run after a filament insert is detected. The default is not to # The gcode to run after a filament insert is detected. The default
# run any gcode commands, which disables insert detection. # is not to run any gcode commands, which disables insert detection.
#event_delay: 3.0 #event_delay: 3.0
# The minimum amount of time in seconds to delay between events. Events # The minimum amount of time in seconds to delay between events.
# triggered during this time period will be silently ignored. The default # Events triggered during this time period will be silently
# is 3 seconds. # ignored. The default is 3 seconds.
#switch_pin: #switch_pin:
# The pin on which the switch is connected. This parameter must be provided. # The pin on which the switch is connected. This parameter must be
# provided.
# TSLl401CL Based Filament Width Sensor
#[tsl1401cl_filament_width_sensor]
#pin: analog5
#default_nominal_filament_diameter: 1.75 # (mm)
# Maximum allowed filament diameter difference as mm
#max_difference: 0.2
# The distance from sensor to the melting chamber as mm
#measurement_delay: 100
# Replicape support - see the generic-replicape.cfg file for further
# details.
#[replicape]