diff --git a/config/example-extras.cfg b/config/example-extras.cfg
index 2c10476a..d301b3b5 100644
--- a/config/example-extras.cfg
+++ b/config/example-extras.cfg
@@ -7,16 +7,6 @@
 # section defining the pins must be listed in the config file before
 # any sections using those pins.
 
-# TSLl401CL Based Filament Width Sensor
-#[tsl1401cl_filament_width_sensor]
-#pin: analog5
-#default_nominal_filament_diameter: 1.75 # (mm)
-#   Maximum allowed filament diameter difference as mm
-#max_difference: 0.2
-#   The distance from sensor to the melting chamber as mm
-#measurement_delay 100
-
-
 
 # Z height probe. One may define this section to enable Z height
 # probing hardware. When this section is enabled, PROBE and
@@ -1379,10 +1369,6 @@
 #   the command invoking the macro.
 
 
-# Replicape support - see the generic-replicape.cfg file for further
-# details.
-#[replicape]
-
 # Enable the "M118" and "RESPOND" extended commands.
 # [respond]
 # default_type: echo
@@ -1395,6 +1381,7 @@
 #    Directly sets the default prefix. If present, this value will override
 #    the "default_type".
 
+
 # The heater_generic section is used to describe a custom/generic heater.
 # These behave the same as typical heaters (extruders, heated beds) and
 # can be configured as similarly.
@@ -1423,6 +1410,7 @@
 #   See the heater section in example.cfg for the definition of the
 #   above parameters.
 
+
 # Temperature sensors. One can define any number of temperature
 # sensors. Their values are reported via the M105 command.
 #[temperature_sensor my_sensor]
@@ -1440,26 +1428,44 @@
 # Pause/Resume functionality with support of position capture and restore
 #[pause_resume]
 #recover_velocity: 50.
-#  When capture/restore is enabled, the speed at which to return to
-#  the captured position (in mm/s).  Default is 50.0 mm/s.
+#   When capture/restore is enabled, the speed at which to return to
+#   the captured position (in mm/s).  Default is 50.0 mm/s.
+
 
 # Filament Switch Sensor.  Support for filament insert and runout detection
 # using a switch sensor, such as an endstop switch.
 #[filament_switch_sensor my_sensor]
 #pause_on_runout: True
-#  When set to True, a PAUSE will execute immediately after a runout is
-#  detected. Note that if pause_on_runout is False and the runout_gcode is
-#  omitted then runout detection is disabled. Default is True.
+#   When set to True, a PAUSE will execute immediately after a runout
+#   is detected. Note that if pause_on_runout is False and the
+#   runout_gcode is omitted then runout detection is disabled. Default
+#   is True.
 #runout_gcode:
-#  The gcode to run after a filament runout is detected.  If pause_on_runout
-#  is set to True this gcode will run after the PAUSE is complete.  The default
-#  is not to run any gcode commands.
+#   The gcode to run after a filament runout is detected. If
+#   pause_on_runout is set to True this gcode will run after the PAUSE
+#   is complete. The default is not to run any gcode commands.
 #insert_gcode:
-#  The gcode to run after a filament insert is detected.  The default is not to
-#  run any gcode commands, which disables insert detection.
+#   The gcode to run after a filament insert is detected. The default
+#   is not to run any gcode commands, which disables insert detection.
 #event_delay: 3.0
-#  The minimum amount of time in seconds to delay between events. Events
-#  triggered during this time period will be silently ignored. The default
-#  is 3 seconds.
+#   The minimum amount of time in seconds to delay between events.
+#   Events triggered during this time period will be silently
+#   ignored. The default is 3 seconds.
 #switch_pin:
-#  The pin on which the switch is connected.  This parameter must be provided.
+#   The pin on which the switch is connected. This parameter must be
+#   provided.
+
+
+# TSLl401CL Based Filament Width Sensor
+#[tsl1401cl_filament_width_sensor]
+#pin: analog5
+#default_nominal_filament_diameter: 1.75 # (mm)
+#   Maximum allowed filament diameter difference as mm
+#max_difference: 0.2
+#   The distance from sensor to the melting chamber as mm
+#measurement_delay: 100
+
+
+# Replicape support - see the generic-replicape.cfg file for further
+# details.
+#[replicape]