config: Use printer-creality-ender3-s1-2021.cfg for both s1 and s1 pro.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

config/printer-creality-ender3-s1-2021.cfg

@@ -1,9 +1,10 @@
 # This file contains pin mappings for the stock 2021 Creality Ender 3
-# S1. To use this config, check the STM32 Chip on the V2.4S1 Board
+# S1 (and S1 pro). To use this config, check the STM32 Chip on the
-# then during "make menuconfig" select either the STM32F103 with a
+# V2.4S1 Board then during "make menuconfig" select either the
-# "28KiB bootloader" or select the STM32F401 with a "64KiB bootloader"
+# STM32F103 with a "28KiB bootloader" or select the STM32F401 with a
-# and serial (on USART1 PA10/PA9) communication for both depending on
+# "64KiB bootloader" and serial (on USART1 PA10/PA9) communication for
-# the STM32 chip installed on your printer's motherboard.
+# both depending on the STM32 chip installed on your printer's
+# motherboard.
 
 # If you prefer a direct serial connection, in "make menuconfig"
 # select "Enable extra low-level configuration options" and select

config/printer-creality-ender3-s1pro-2022.cfg

@@ -1,130 +0,0 @@
-# This file contains pin mappings for the stock 2022 Creality Ender 3
-# S1 Pro. To use this config, check the STM32 Chip on the V2.4S1 Board
-# then during "make menuconfig" select either the STM32F103 with a
-# "28KiB bootloader" or select the STM32F401 with a "64KiB bootloader"
-# and serial (on USART1 PA10/PA9) communication for both depending on
-# the STM32 chip installed on your printer's motherboard.
-
-# If you prefer a direct serial connection, in "make menuconfig"
-# select "Enable extra low-level configuration options" and select
-# Serial (on USART2 PA3/PA2), which is broken out on the 10 pin IDC
-# cable used for the LCD module as follows:
-# 3: Tx, 4: Rx, 9: GND, 10: VCC
-
-# Flash this firmware by copying "out/klipper.bin" to a SD card and
-# turning on the printer with the card inserted. The firmware
-# filename must changed to "firmware.bin"
-
-# See docs/Config_Reference.md for a description of parameters.
-
-[stepper_x]
-step_pin: PC2
-dir_pin: PB9
-enable_pin: !PC3
-microsteps: 16
-rotation_distance: 40
-endstop_pin: !PA5
-position_endstop: -10
-position_max: 235
-position_min: -15
-homing_speed: 50
-
-[stepper_y]
-step_pin: PB8
-dir_pin: PB7
-enable_pin: !PC3
-microsteps: 16
-rotation_distance: 40
-endstop_pin: !PA6
-position_endstop: -10
-position_max: 241
-position_min: -15
-homing_speed: 50
-
-[stepper_z]
-step_pin: PB6
-dir_pin: !PB5
-enable_pin: !PC3
-microsteps: 16
-rotation_distance: 8
-endstop_pin: probe:z_virtual_endstop
-position_max: 270
-position_min: -4
-
-[extruder]
-step_pin: PB4
-dir_pin: PB3
-enable_pin: !PC3
-microsteps: 16
-gear_ratio: 42:12
-rotation_distance: 26.359
-nozzle_diameter: 0.400
-filament_diameter: 1.750
-heater_pin: PA1
-sensor_type: EPCOS 100K B57560G104F
-sensor_pin: PC5
-control: pid
-pid_Kp: 23.561
-pid_Ki: 1.208
-pid_Kd: 114.859
-min_temp: 0
-max_temp: 300
-
-[heater_bed]
-heater_pin: PA7
-sensor_type: EPCOS 100K B57560G104F
-sensor_pin: PC4
-control: pid
-pid_Kp: 71.867
-pid_Ki: 1.536
-pid_Kd: 840.843
-min_temp: 0
-max_temp: 110
-
-[heater_fan hotend_fan]
-pin: PC0
-
-[fan]
-pin: PA0
-
-[mcu]
-serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
-restart_method: command
-
-[printer]
-kinematics: cartesian
-max_velocity: 300
-max_accel: 2000
-max_z_velocity: 5
-max_z_accel: 100
-
-[bltouch]
-sensor_pin: ^PC14
-control_pin: PC13
-x_offset: -31.8
-y_offset: -40.5
-z_offset: 0
-probe_with_touch_mode: true
-stow_on_each_sample: false
-
-[bed_mesh]
-speed: 120
-mesh_min: 20, 20
-mesh_max: 200, 200
-probe_count: 4,4
-algorithm: bicubic
-
-[safe_z_home]
-home_xy_position: 147, 154
-speed: 75
-z_hop: 5
-z_hop_speed: 5
-move_to_previous: true
-
-[filament_switch_sensor e0_sensor]
-switch_pin: !PC15
-pause_on_runout: true
-runout_gcode: PAUSE
-
-[pause_resume]
-recover_velocity: 25

test/klippy/printers.test

@@ -161,7 +161,6 @@ CONFIG ../../config/printer-creality-cr6se-2020.cfg
 CONFIG ../../config/printer-creality-cr6se-2021.cfg
 CONFIG ../../config/printer-creality-ender2pro-2021.cfg
 CONFIG ../../config/printer-creality-ender3-s1-2021.cfg
-CONFIG ../../config/printer-creality-ender3-s1pro-2022.cfg
 CONFIG ../../config/printer-creality-ender3-v2-2020.cfg
 CONFIG ../../config/printer-creality-ender3max-2021.cfg
 CONFIG ../../config/printer-creality-ender3pro-2020.cfg