config: Add generic-melzi.cfg file for Melzi boards
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
3506d1e994
commit
3033b03789
|
@ -0,0 +1,76 @@
|
|||
# This file contains common pin mappings for Melzi v2.0 boards. To use
|
||||
# this config, the firmware should be compiled for the AVR
|
||||
# atmega1284p.
|
||||
|
||||
# Note that the "make flash" command does not work with Melzi
|
||||
# boards. The boards are typically flashed with this command:
|
||||
# avrdude -p atmega1284p -c avrisp -P /dev/ttyUSB0 -U flash:w:out/klipper.elf.hex
|
||||
|
||||
# See the example.cfg file for a description of available parameters.
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PD7
|
||||
dir_pin: PC5
|
||||
enable_pin: !PD6
|
||||
step_distance: .0125
|
||||
endstop_pin: ^!PC2
|
||||
position_endstop: 0
|
||||
position_max: 200
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PC6
|
||||
dir_pin: PC7
|
||||
enable_pin: !PD6
|
||||
step_distance: .0125
|
||||
endstop_pin: ^!PC3
|
||||
position_endstop: 0
|
||||
position_max: 200
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB3
|
||||
dir_pin: !PB2
|
||||
enable_pin: !PA5
|
||||
step_distance: 0.00025
|
||||
endstop_pin: ^!PC4
|
||||
position_endstop: 0.5
|
||||
position_max: 200
|
||||
|
||||
[extruder]
|
||||
step_pin: PB1
|
||||
dir_pin: PB0
|
||||
enable_pin: !PD6
|
||||
step_distance: .002
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PD5
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PA7
|
||||
control: pid
|
||||
pid_Kp: 22.2
|
||||
pid_Ki: 1.08
|
||||
pid_Kd: 114
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PD2
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PA6
|
||||
control: watermark
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PB4
|
||||
|
||||
[mcu]
|
||||
serial: /dev/ttyUSB0
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
Loading…
Reference in New Issue