3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

config: Anycubic 4 Max Pro 2.0 - Added two internal systems (beeper and PSU control). (#5629) 

Signed-off-by: Usachev Alexander Valer'evich <int_0x21@protonmail.com>
This commit is contained in:
int_0x03 2022-08-19 20:11:42 +03:00 committed by GitHub
parent 2357221bb4
commit 20a28bc00f
No known key found for this signature in database
GPG Key ID: 4AEE18F83AFDEB23
1 changed files with 48 additions and 1 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

49
config/printer-anycubic-4maxpro-2.0-2021.cfg
View File

@ -11,7 +11,7 @@
# For Anycubic 4Max Pro (not 2.0) owners: # For Anycubic 4Max Pro (not 2.0) owners:
# Be careful when using this config! This config tested only on Anycubic # Be careful when using this config! This config tested only on Anycubic
# 4Max Pro 2.0 with klipper v0.9.1-667-g31761500! At first, you should # 4Max Pro 2.0! At first, you should
# set homing_speed on 5, and run homing and click on the endstops with # set homing_speed on 5, and run homing and click on the endstops with
# your fingers. It is necessary to make sure that all the motors are # your fingers. It is necessary to make sure that all the motors are
# spinning in the right direction, all the temperature sensors show the # spinning in the right direction, all the temperature sensors show the
@ -139,3 +139,50 @@ screw4: 265, 5
[filament_switch_sensor filament_sensor] [filament_switch_sensor filament_sensor]
switch_pin: ^!PC4 switch_pin: ^!PC4
[output_pin buzz]
pin: PC6
pwm: True
[output_pin AUTO_POWEROFF]
pin: PD0
pwm: True
cycle_time: 0.02
value: 1
# This macro (M300) uses internal integrated beeper
# Just use it in your G-code for making sounds. Example: M300 S1000 P500
[gcode_macro M300]
gcode:
{% set S = params.S|default(800)|float %}
{% set P = params.P|default(100)|int %}
SET_PIN PIN=buzz VALUE=0.5 CYCLE_TIME={ 1.0 / S | float }
G4 P{P}
SET_PIN PIN=buzz VALUE=0
# This macro (M81) uses internal integrated PSU control-relay.
# Just use M81 in your end_gcode if you want to poweroff your printer after print.
# Note: as in original Marlin firmware, before powerdown, printer will be cool hotend
# until temperature will be below 45°С / 113°F.
[gcode_macro M81]
gcode:
{% set required_extruder_temp = params.T|default(45)|int %}
{% if printer.extruder.temperature > required_extruder_temp|default(45)|int %}
M300
M300
M300
M117 COOLING DOWN BEFORE POWER OFF
M109 S{required_extruder_temp}
SET_PIN PIN=AUTO_POWEROFF VALUE=0.5
G4 P60
SET_PIN PIN=AUTO_POWEROFF VALUE=1
{% else %}
M300
M117 POWER OFF SOON
G4 P10000
SET_PIN PIN=AUTO_POWEROFF VALUE=0.5
G4 P60
SET_PIN PIN=AUTO_POWEROFF VALUE=1
{% endif %}