adc_scaled: Add support for Duet2 Maestro "vref monitoring"
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
9b2816477b
commit
1f5848fc1a
|
@ -2222,6 +2222,23 @@
|
|||
# communication. The pin must have a valid pinmux configuration
|
||||
# for the given SERCOM peripheral. This parameter must be provided.
|
||||
|
||||
# Duet2 Maestro analog scaling by vref and vssa readings. Defining an
|
||||
# adc_scaled section enables virtual adc pins (such as "my_name:PB0")
|
||||
# that are automatically adjusted by the board's vref and vssa
|
||||
# monitoring pins. Be sure to define this config section above any
|
||||
# config sections that use one these virtual pins.
|
||||
#[adc_scaled my_name]
|
||||
#vref_pin:
|
||||
# The ADC pin to use for VREF monitoring. This parameter must be
|
||||
# provided.
|
||||
#vssa_pin:
|
||||
# The ADC pin to use for VSSA monitoring. This parameter must be
|
||||
# provided.
|
||||
#smooth_time: 2.0
|
||||
# A time value (in seconds) over which the vref and vssa
|
||||
# measurements will be smoothed to reduce the impact of measurement
|
||||
# noise. The default is 2 seconds.
|
||||
|
||||
# Replicape support - see the generic-replicape.cfg file for further
|
||||
# details.
|
||||
#[replicape]
|
||||
|
|
|
@ -59,6 +59,11 @@ microsteps: 16
|
|||
run_current: 0.800
|
||||
stealthchop_threshold: 30
|
||||
|
||||
# Support analog sensor adjustments using VREF/VSSA pins
|
||||
[adc_scaled vref_scaled]
|
||||
vref_pin: PA17
|
||||
vssa_pin: PA19
|
||||
|
||||
[extruder]
|
||||
step_pin: PC4
|
||||
dir_pin: PB7
|
||||
|
@ -69,7 +74,7 @@ filament_diameter: 1.750
|
|||
heater_pin: !PC1
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
pullup_resistor: 2200
|
||||
sensor_pin: PB0
|
||||
sensor_pin: vref_scaled:PB0
|
||||
control: pid
|
||||
pid_Kp: 22.2
|
||||
pid_Ki: 1.08
|
||||
|
@ -110,7 +115,7 @@ stealthchop_threshold: 5
|
|||
heater_pin: !PC0
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
pullup_resistor: 2200
|
||||
sensor_pin: PA20
|
||||
sensor_pin: vref_scaled:PA20
|
||||
control: watermark
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
|
|
@ -0,0 +1,79 @@
|
|||
# Support for scaling ADC values based on measured VREF and VSSA
|
||||
#
|
||||
# Copyright (C) 2020 Kevin O'Connor <kevin@koconnor.net>
|
||||
#
|
||||
# This file may be distributed under the terms of the GNU GPLv3 license.
|
||||
|
||||
SAMPLE_TIME = 0.001
|
||||
SAMPLE_COUNT = 8
|
||||
REPORT_TIME = 0.300
|
||||
RANGE_CHECK_COUNT = 4
|
||||
|
||||
class MCU_scaled_adc:
|
||||
def __init__(self, main, pin_params):
|
||||
self._main = main
|
||||
self._last_state = (0., 0.)
|
||||
self._mcu_adc = main.mcu.setup_pin('adc', pin_params)
|
||||
query_adc = main.printer.lookup_object('query_adc')
|
||||
qname = main.name + ":" + pin_params['pin']
|
||||
query_adc.register_adc(qname, self._mcu_adc)
|
||||
self._callback = None
|
||||
self.setup_minmax = self._mcu_adc.setup_minmax
|
||||
self.get_mcu = self._mcu_adc.get_mcu
|
||||
def _handle_callback(self, read_time, read_value):
|
||||
max_adc = self._main.last_vref[1]
|
||||
min_adc = self._main.last_vssa[1]
|
||||
scaled_val = (read_value - min_adc) / (max_adc - min_adc)
|
||||
self._last_state = (scaled_val, read_time)
|
||||
self._callback(read_time, scaled_val)
|
||||
def setup_adc_callback(self, report_time, callback):
|
||||
self._callback = callback
|
||||
self._mcu_adc.setup_adc_callback(report_time, self._handle_callback)
|
||||
def get_last_value(self):
|
||||
return self._last_state
|
||||
|
||||
class PrinterADCScaled:
|
||||
def __init__(self, config):
|
||||
self.printer = config.get_printer()
|
||||
self.name = config.get_name().split()[1]
|
||||
self.last_vref = (0., 0.)
|
||||
self.last_vssa = (0., 0.)
|
||||
# Configure vref and vssa pins
|
||||
self.mcu_vref = self._config_pin(config, 'vref', self.vref_callback)
|
||||
self.mcu_vssa = self._config_pin(config, 'vssa', self.vssa_callback)
|
||||
smooth_time = config.getfloat('smooth_time', 2., above=0.)
|
||||
self.inv_smooth_time = 1. / smooth_time
|
||||
self.mcu = self.mcu_vref.get_mcu()
|
||||
if self.mcu is not self.mcu_vssa.get_mcu():
|
||||
raise config.error("vref and vssa must be on same mcu")
|
||||
# Register setup_pin
|
||||
ppins = self.printer.lookup_object('pins')
|
||||
ppins.register_chip(self.name, self)
|
||||
def _config_pin(self, config, name, callback):
|
||||
pin_name = config.get(name + '_pin')
|
||||
ppins = self.printer.lookup_object('pins')
|
||||
mcu_adc = ppins.setup_pin('adc', pin_name)
|
||||
mcu_adc.setup_adc_callback(REPORT_TIME, callback)
|
||||
mcu_adc.setup_minmax(SAMPLE_TIME, SAMPLE_COUNT, minval=0., maxval=1.,
|
||||
range_check_count=RANGE_CHECK_COUNT)
|
||||
query_adc = config.get_printer().load_object(config, 'query_adc')
|
||||
query_adc.register_adc(self.name + ":" + name, mcu_adc)
|
||||
return mcu_adc
|
||||
def setup_pin(self, pin_type, pin_params):
|
||||
if pin_type != 'adc':
|
||||
raise self.printer.config_error("adc_scaled only supports adc pins")
|
||||
return MCU_scaled_adc(self, pin_params)
|
||||
def calc_smooth(self, read_time, read_value, last):
|
||||
last_time, last_value = last
|
||||
time_diff = read_time - last_time
|
||||
value_diff = read_value - last_value
|
||||
adj_time = min(time_diff * self.inv_smooth_time, 1.)
|
||||
smoothed_value = last_value + value_diff * adj_time
|
||||
return (read_time, smoothed_value)
|
||||
def vref_callback(self, read_time, read_value):
|
||||
self.last_vref = self.calc_smooth(read_time, read_value, self.last_vref)
|
||||
def vssa_callback(self, read_time, read_value):
|
||||
self.last_vssa = self.calc_smooth(read_time, read_value, self.last_vssa)
|
||||
|
||||
def load_config_prefix(config):
|
||||
return PrinterADCScaled(config)
|
Loading…
Reference in New Issue