config: Add config for printer Creality CR10s Pro V2 (#6300)
Created a base config for the Creality CR10s Pro v2 as described here: https://www.creality.com/products/cr-10s-pro-v2-3d-printer This will allow users with this printer to more easily setup Klipper firmware. Signed-off-by: Peter Kydas <peter@kydas.me>
This commit is contained in:
parent
dd368c107c
commit
15c3824e9b
|
@ -0,0 +1,154 @@
|
|||
# This file contains pin mappings for the Creality CR-10S Pro V2. To use
|
||||
# this config, the firmware should be compiled for the AVR atmega2560.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
## General Config
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/<YOUR_USB_ID>
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 200
|
||||
max_accel: 1500
|
||||
max_z_velocity: 10
|
||||
max_z_accel: 100
|
||||
|
||||
## Stepper Motors and Extruder
|
||||
[stepper_x]
|
||||
step_pin: PF0 #ar54
|
||||
dir_pin: PF1 #ar55
|
||||
enable_pin: !PD7 #!ar38
|
||||
rotation_distance: 40
|
||||
microsteps: 16
|
||||
full_steps_per_rotation: 200
|
||||
endstop_pin: ^PE5 #^ar3
|
||||
position_endstop: 0
|
||||
position_min: 0
|
||||
position_max: 300
|
||||
homing_speed: 50
|
||||
homing_retract_dist: 5
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PF6 #ar60
|
||||
dir_pin: !PF7 #ar61
|
||||
enable_pin: !PF2 #!ar56
|
||||
rotation_distance: 40
|
||||
microsteps: 16
|
||||
full_steps_per_rotation: 200
|
||||
endstop_pin: ^PJ1 #^ar14
|
||||
position_endstop: 0
|
||||
position_min: 0
|
||||
position_max: 310
|
||||
homing_speed: 50
|
||||
homing_retract_dist: 5
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PL3 #ar46
|
||||
dir_pin: !PL1 #!ar48
|
||||
enable_pin: !PK0 #!ar62
|
||||
rotation_distance: 8
|
||||
microsteps: 16
|
||||
full_steps_per_rotation: 200
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
position_min: -3
|
||||
position_max: 363 # you can go higher but then the cables crimp
|
||||
|
||||
[extruder]
|
||||
step_pin: PA4 # ar26
|
||||
dir_pin: PA6 # !ar28
|
||||
enable_pin: !PA2 # !ar24
|
||||
rotation_distance: 22.900
|
||||
microsteps: 16
|
||||
full_steps_per_rotation: 200
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
max_extrude_only_distance: 500.0
|
||||
max_extrude_only_velocity: 70.0
|
||||
max_extrude_only_accel: 1000.0
|
||||
heater_pin: PB4 #ar10
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PK5 #analog13
|
||||
control: pid #calibrated in Klipper, you will need to run this for your machine
|
||||
pid_kp: 28.359
|
||||
pid_ki: 1.616
|
||||
pid_kd: 124.426
|
||||
min_extrude_temp: 170
|
||||
min_temp: 5
|
||||
max_temp: 275
|
||||
|
||||
[fan]
|
||||
pin: PH6 #ar9
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PH5 #ar8
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PK6 #analog14
|
||||
control: pid #calibrated in Klipper, you will need to run this for your machine
|
||||
pid_kp: 70.936
|
||||
pid_ki: 1.151
|
||||
pid_kd: 1093.298
|
||||
min_temp: 5
|
||||
max_temp: 140
|
||||
|
||||
## BLTouch and Safe Z Settings
|
||||
[bltouch]
|
||||
sensor_pin: ^PD2
|
||||
control_pin: PB5
|
||||
stow_on_each_sample: False # Be careful
|
||||
probe_with_touch_mode: True
|
||||
x_offset: -27
|
||||
y_offset: -2
|
||||
z_offset: 2 # you will need to calibrate this in Klipper
|
||||
speed: 4.0
|
||||
samples: 2
|
||||
sample_retract_dist: 3.0
|
||||
|
||||
[safe_z_home]
|
||||
home_xy_position: 177,155
|
||||
speed: 80.0
|
||||
z_hop: 10.0
|
||||
z_hop_speed: 5.0
|
||||
|
||||
[bed_mesh]
|
||||
speed: 120
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 5, 5
|
||||
mesh_max: 268, 305
|
||||
probe_count: 5,5
|
||||
fade_start: 1
|
||||
fade_end: 10
|
||||
|
||||
[filament_switch_sensor e0_sensor]
|
||||
switch_pin: PE4 #ar2
|
||||
pause_on_runout: False
|
||||
runout_gcode:
|
||||
PAUSE_PARK
|
||||
|
||||
## Calibrating the Bed
|
||||
# this is for the bltouch to calibrate the bed
|
||||
[screws_tilt_adjust]
|
||||
screw1: 40,40
|
||||
screw1_name: front left screw
|
||||
screw2: 295,40
|
||||
screw2_name: front right screw
|
||||
screw3: 295,280
|
||||
screw3_name: rear right screw
|
||||
screw4: 40,280
|
||||
screw4_name: rear left screw
|
||||
speed: 50
|
||||
horizontal_move_z: 10
|
||||
screw_thread: CW-M3
|
||||
|
||||
[bed_screws]
|
||||
screw1: 13,38
|
||||
screw1_name: front left screw
|
||||
screw2: 268,38
|
||||
screw2_name: front right screw
|
||||
screw3: 268,278
|
||||
screw3_name: rear right screw
|
||||
screw4: 13,38
|
||||
screw4_name: rear left screw
|
||||
horizontal_move_z: 5
|
||||
|
||||
[pause_resume]
|
|
@ -34,6 +34,7 @@ CONFIG ../../config/printer-bq-hephestos-2014.cfg
|
|||
CONFIG ../../config/printer-creality-cr5pro-ht-2022.cfg
|
||||
CONFIG ../../config/printer-creality-cr10-v3-2020.cfg
|
||||
CONFIG ../../config/printer-creality-cr10s-2017.cfg
|
||||
CONFIG ../../config/printer-creality-cr10s-pro-v2-2020.cfg
|
||||
CONFIG ../../config/printer-creality-cr20-2018.cfg
|
||||
CONFIG ../../config/printer-creality-cr20-pro-2019.cfg
|
||||
CONFIG ../../config/printer-creality-ender5plus-2019.cfg
|
||||
|
|
Loading…
Reference in New Issue