config: Add a generic-creality-v4.2.7.cfg example config
Reported by @Feche and @yjh0502 . Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
48b30e0f5a
commit
0bf0cb5b54
|
@ -0,0 +1,88 @@
|
||||||
|
# This file contains pin mappings for the Creality "v4.2.7" board. To
|
||||||
|
# use this config, during "make menuconfig" select the STM32F103 with
|
||||||
|
# a "28KiB bootloader" and with "Use USB for communication" disabled.
|
||||||
|
|
||||||
|
# If you prefer a direct serial connection, in "make menuconfig"
|
||||||
|
# select "Enable extra low-level configuration options" and select the
|
||||||
|
# USART3 serial port, which is broken out on the 10 pin IDC cable used
|
||||||
|
# for the LCD module as follows:
|
||||||
|
# 3: Tx, 4: Rx, 9: GND, 10: VCC
|
||||||
|
|
||||||
|
# Flash this firmware by copying "out/klipper.bin" to a SD card and
|
||||||
|
# turning on the printer with the card inserted. The firmware
|
||||||
|
# filename must end in ".bin" and must not match the last filename
|
||||||
|
# that was flashed.
|
||||||
|
|
||||||
|
# See the example.cfg file for a description of available parameters.
|
||||||
|
|
||||||
|
[stepper_x]
|
||||||
|
step_pin: PB9
|
||||||
|
dir_pin: PC2
|
||||||
|
enable_pin: !PC3
|
||||||
|
step_distance: .0125
|
||||||
|
endstop_pin: ^PA5
|
||||||
|
position_endstop: 0
|
||||||
|
position_max: 235
|
||||||
|
homing_speed: 50
|
||||||
|
|
||||||
|
[stepper_y]
|
||||||
|
step_pin: PB7
|
||||||
|
dir_pin: PB8
|
||||||
|
enable_pin: !PC3
|
||||||
|
step_distance: .0125
|
||||||
|
endstop_pin: ^PA6
|
||||||
|
position_endstop: 0
|
||||||
|
position_max: 235
|
||||||
|
homing_speed: 50
|
||||||
|
|
||||||
|
[stepper_z]
|
||||||
|
step_pin: PB5
|
||||||
|
dir_pin: !PB6
|
||||||
|
enable_pin: !PC3
|
||||||
|
step_distance: .0025
|
||||||
|
endstop_pin: ^PA7
|
||||||
|
position_endstop: 0.0
|
||||||
|
position_max: 250
|
||||||
|
|
||||||
|
[extruder]
|
||||||
|
max_extrude_only_distance: 100.0
|
||||||
|
step_pin: PB3
|
||||||
|
dir_pin: PB4
|
||||||
|
enable_pin: !PC3
|
||||||
|
step_distance: 0.010752
|
||||||
|
nozzle_diameter: 0.400
|
||||||
|
filament_diameter: 1.750
|
||||||
|
heater_pin: PA1
|
||||||
|
sensor_type: EPCOS 100K B57560G104F
|
||||||
|
sensor_pin: PC5
|
||||||
|
control: pid
|
||||||
|
pid_Kp: 21.527
|
||||||
|
pid_Ki: 1.063
|
||||||
|
pid_Kd: 108.982
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 250
|
||||||
|
|
||||||
|
[heater_bed]
|
||||||
|
heater_pin: PA2
|
||||||
|
sensor_type: EPCOS 100K B57560G104F
|
||||||
|
sensor_pin: PC4
|
||||||
|
control: pid
|
||||||
|
pid_Kp: 54.027
|
||||||
|
pid_Ki: 0.770
|
||||||
|
pid_Kd: 948.182
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 130
|
||||||
|
|
||||||
|
[fan]
|
||||||
|
pin: PA0
|
||||||
|
|
||||||
|
[mcu]
|
||||||
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||||||
|
restart_method: command
|
||||||
|
|
||||||
|
[printer]
|
||||||
|
kinematics: cartesian
|
||||||
|
max_velocity: 300
|
||||||
|
max_accel: 3000
|
||||||
|
max_z_velocity: 5
|
||||||
|
max_z_accel: 100
|
|
@ -121,6 +121,7 @@ CONFIG ../../config/generic-bigtreetech-skr-e3-dip.cfg
|
||||||
|
|
||||||
# Printers using the stm32f103 via serial
|
# Printers using the stm32f103 via serial
|
||||||
DICTIONARY stm32f103-serial.dict
|
DICTIONARY stm32f103-serial.dict
|
||||||
|
CONFIG ../../config/generic-creality-v4.2.7.cfg
|
||||||
CONFIG ../../config/generic-fysetc-cheetah-v1.1.cfg
|
CONFIG ../../config/generic-fysetc-cheetah-v1.1.cfg
|
||||||
CONFIG ../../config/generic-fysetc-cheetah-v1.2.cfg
|
CONFIG ../../config/generic-fysetc-cheetah-v1.2.cfg
|
||||||
CONFIG ../../config/generic-mks-robin-e3.cfg
|
CONFIG ../../config/generic-mks-robin-e3.cfg
|
||||||
|
|
Loading…
Reference in New Issue