config: Add a generic-creality-v4.2.7.cfg example config

Reported by @Feche and @yjh0502 .

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
Kevin O'Connor 2020-09-29 11:45:44 -04:00
parent 48b30e0f5a
commit 0bf0cb5b54
2 changed files with 89 additions and 0 deletions

View File

@ -0,0 +1,88 @@
# This file contains pin mappings for the Creality "v4.2.7" board. To
# use this config, during "make menuconfig" select the STM32F103 with
# a "28KiB bootloader" and with "Use USB for communication" disabled.
# If you prefer a direct serial connection, in "make menuconfig"
# select "Enable extra low-level configuration options" and select the
# USART3 serial port, which is broken out on the 10 pin IDC cable used
# for the LCD module as follows:
# 3: Tx, 4: Rx, 9: GND, 10: VCC
# Flash this firmware by copying "out/klipper.bin" to a SD card and
# turning on the printer with the card inserted. The firmware
# filename must end in ".bin" and must not match the last filename
# that was flashed.
# See the example.cfg file for a description of available parameters.
[stepper_x]
step_pin: PB9
dir_pin: PC2
enable_pin: !PC3
step_distance: .0125
endstop_pin: ^PA5
position_endstop: 0
position_max: 235
homing_speed: 50
[stepper_y]
step_pin: PB7
dir_pin: PB8
enable_pin: !PC3
step_distance: .0125
endstop_pin: ^PA6
position_endstop: 0
position_max: 235
homing_speed: 50
[stepper_z]
step_pin: PB5
dir_pin: !PB6
enable_pin: !PC3
step_distance: .0025
endstop_pin: ^PA7
position_endstop: 0.0
position_max: 250
[extruder]
max_extrude_only_distance: 100.0
step_pin: PB3
dir_pin: PB4
enable_pin: !PC3
step_distance: 0.010752
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA1
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC5
control: pid
pid_Kp: 21.527
pid_Ki: 1.063
pid_Kd: 108.982
min_temp: 0
max_temp: 250
[heater_bed]
heater_pin: PA2
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC4
control: pid
pid_Kp: 54.027
pid_Ki: 0.770
pid_Kd: 948.182
min_temp: 0
max_temp: 130
[fan]
pin: PA0
[mcu]
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
restart_method: command
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100

View File

@ -121,6 +121,7 @@ CONFIG ../../config/generic-bigtreetech-skr-e3-dip.cfg
# Printers using the stm32f103 via serial
DICTIONARY stm32f103-serial.dict
CONFIG ../../config/generic-creality-v4.2.7.cfg
CONFIG ../../config/generic-fysetc-cheetah-v1.1.cfg
CONFIG ../../config/generic-fysetc-cheetah-v1.2.cfg
CONFIG ../../config/generic-mks-robin-e3.cfg