config: I3DBEEZ9 New board (#6447)
Signed-off-by: Venkata Kamesh <i3dbee@gmail.com>
This commit is contained in:
parent
92fe8f15b8
commit
0665dc8976
|
@ -0,0 +1,223 @@
|
|||
# This file contains common pin mappings for the I3DBEEZ9 V1.0.
|
||||
# To use this config, the firmware should be compiled for the
|
||||
# STM32F407 with a "32KiB bootloader".
|
||||
|
||||
# The "make flash" command does not work on the I3DBEEZ9. Instead,
|
||||
# after running "make", copy the generated "out/klipper.bin" file to a
|
||||
# file named "firmware.bin" on an SD card and then restart the I3DBEEZ9
|
||||
# with that SD card.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PE9
|
||||
dir_pin: PF1
|
||||
enable_pin: !PF2
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: PB10
|
||||
position_endstop: 0
|
||||
position_max: 200
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PE11
|
||||
dir_pin: PE1
|
||||
enable_pin: !PD7
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: PE12
|
||||
position_endstop: 0
|
||||
position_max: 200
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PE13
|
||||
dir_pin: PC2
|
||||
enable_pin: !PC0
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: PG8
|
||||
position_endstop: 0
|
||||
position_max: 200
|
||||
|
||||
[extruder]
|
||||
step_pin: PE14
|
||||
dir_pin: PA0
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 33.500
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PB1 # Heat0
|
||||
sensor_pin: PF4 # T1 Header
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
control: pid
|
||||
pid_Kp: 22.2
|
||||
pid_Ki: 1.08
|
||||
pid_Kd: 114
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
#[extruder1]
|
||||
#step_pin: PD15
|
||||
#dir_pin: PE7
|
||||
#enable_pin: !PA3
|
||||
#heater_pin: PD14 # Heat1
|
||||
#sensor_pin: PF5 # T2
|
||||
#...
|
||||
|
||||
#[extruder2]
|
||||
#step_pin: PD13
|
||||
#dir_pin: PG9
|
||||
#enable_pin: !PF0
|
||||
#heater_pin: PB0 # Heat2
|
||||
#sensor_pin: PF6 # T3
|
||||
#...
|
||||
|
||||
#[stepper_z1]
|
||||
#step_pin: PE4
|
||||
#dir_pin: PE3
|
||||
#enable_pin: !PC13
|
||||
#microsteps: 16
|
||||
#rotation_distance: 8
|
||||
#endstop_pin: PD0
|
||||
#position_endstop: 0.5
|
||||
#position_max: 200
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PD12
|
||||
sensor_pin: PF3 # T0
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
control: watermark
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PC8
|
||||
|
||||
[heater_fan fan1]
|
||||
pin: PE5
|
||||
|
||||
#[heater_fan fan2]
|
||||
#pin: PE6
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
|
||||
########################################
|
||||
# TMC2208 configuration
|
||||
########################################
|
||||
|
||||
#[tmc2208 stepper_x]
|
||||
#uart_pin: PA15
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2208 stepper_y]
|
||||
#uart_pin: PB8
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2208 stepper_z]
|
||||
#uart_pin: PB9
|
||||
#run_current: 0.650
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2208 extruder]
|
||||
#uart_pin: PB3
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2208 extruder1]
|
||||
#uart_pin: PG15
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2208 extruder2]
|
||||
#uart_pin: PG12
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2208 stepper_z1]
|
||||
#uart_pin: PE2
|
||||
#run_current: 0.650
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
########################################
|
||||
# TMC2130 configuration
|
||||
########################################
|
||||
|
||||
#[tmc2130 stepper_x]
|
||||
#cs_pin: PA15
|
||||
#spi_bus: spi3a
|
||||
##diag1_pin: PB10
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 stepper_y]
|
||||
#cs_pin: PB8
|
||||
#spi_bus: spi3a
|
||||
##diag1_pin: PE12
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 stepper_z]
|
||||
#cs_pin: PB9
|
||||
#spi_bus: spi3a
|
||||
##diag1_pin: PG8
|
||||
#run_current: 0.650
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 extruder]
|
||||
#cs_pin: PB3
|
||||
#spi_bus: spi3a
|
||||
##diag1_pin: PE15
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 extruder1]
|
||||
#cs_pin: PG15
|
||||
#spi_bus: spi3a
|
||||
##diag1_pin: PE10
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 extruder2]
|
||||
#cs_pin: PG12
|
||||
#spi_bus: spi3a
|
||||
##diag1_pin: PG5
|
||||
#run_current: 0.800
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
#[tmc2130 stepper_z1]
|
||||
#cs_pin: PE2
|
||||
#spi_bus: spi3a
|
||||
##diag1_pin: PD0
|
||||
#run_current: 0.650
|
||||
#stealthchop_threshold: 999999
|
||||
|
||||
|
||||
########################################
|
||||
# EXP1 / EXP2 (display) pins
|
||||
########################################
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PG4, EXP1_3=PD11, EXP1_5=PG2, EXP1_7=PG6, EXP1_9=<GND>,
|
||||
EXP1_2=PA8, EXP1_4=PD10, EXP1_6=PG3, EXP1_8=PG7, EXP1_10=<5V>,
|
||||
# EXP2 header
|
||||
EXP2_1=PB14, EXP2_3=PG10, EXP2_5=PF11, EXP2_7=PF12, EXP2_9=<GND>,
|
||||
EXP2_2=PB13, EXP2_4=PB12, EXP2_6=PB15, EXP2_8=<RST>, EXP2_10=PF13
|
||||
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi2"
|
||||
|
||||
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
|
@ -219,6 +219,7 @@ CONFIG ../../config/generic-bigtreetech-gtr.cfg
|
|||
CONFIG ../../config/generic-bigtreetech-skr-pro.cfg
|
||||
CONFIG ../../config/generic-bigtreetech-skr-2.cfg
|
||||
CONFIG ../../config/generic-flyboard.cfg
|
||||
CONFIG ../../config/generic-I3DBEEZ9.cfg
|
||||
CONFIG ../../config/generic-mellow-fly-cdy-v3.cfg
|
||||
CONFIG ../../config/generic-mellow-super-infinty-hv.cfg
|
||||
CONFIG ../../config/generic-mks-monster8.cfg
|
||||
|
@ -228,6 +229,8 @@ CONFIG ../../config/generic-th3d-ezboard-v2.0.cfg
|
|||
CONFIG ../../config/printer-biqu-b1-se-plus-2022.cfg
|
||||
CONFIG ../../config/printer-prusa-mini-plus-2020.cfg
|
||||
|
||||
|
||||
|
||||
# Printers using the stm32f429
|
||||
DICTIONARY stm32f429.dict
|
||||
CONFIG ../../config/generic-bigtreetech-octopus-v1.1.cfg
|
||||
|
|
Loading…
Reference in New Issue