config: Add printer-tevo-flash-2018.cfg
Reported by @RadianceNL. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
4718f39b2f
commit
01c8705d92
|
@ -0,0 +1,118 @@
|
|||
# Support for Tevo Flash using a Bondtech BMG extruder. To use this
|
||||
# config, the firmware should be compiled for the AVR atmega2560.
|
||||
|
||||
[stepper_x]
|
||||
step_pin: ar54
|
||||
dir_pin: !ar55
|
||||
enable_pin: !ar38
|
||||
step_distance: .012491
|
||||
endstop_pin: !ar3
|
||||
position_endstop: -13
|
||||
position_min: -13
|
||||
position_max: 235
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_y]
|
||||
step_pin: ar60
|
||||
dir_pin: ar61
|
||||
enable_pin: !ar56
|
||||
step_distance: .012441
|
||||
endstop_pin: !ar14
|
||||
position_endstop: -3
|
||||
position_min: -3
|
||||
position_max: 235
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_z]
|
||||
step_pin: ar46
|
||||
dir_pin: ar48
|
||||
enable_pin: !ar62
|
||||
step_distance: .002520
|
||||
position_max: 250
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
position_min: -2
|
||||
|
||||
[stepper_z1]
|
||||
step_pin: ar36
|
||||
dir_pin: ar34
|
||||
enable_pin: !ar30
|
||||
step_distance: .002520
|
||||
|
||||
[extruder]
|
||||
step_pin: ar26
|
||||
dir_pin: ar28
|
||||
enable_pin: !ar24
|
||||
step_distance: .002401
|
||||
nozzle_diameter: 0.600
|
||||
filament_diameter: 1.750
|
||||
heater_pin: ar10
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: analog13
|
||||
control: pid
|
||||
pid_Kp: 18.547
|
||||
pid_Ki: 0.788
|
||||
pid_Kd: 109.193
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: ar8
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: analog14
|
||||
control: pid
|
||||
pid_Kp: 38.824
|
||||
pid_Ki: 0.539
|
||||
pid_Kd: 698.838
|
||||
min_temp: 0
|
||||
max_temp: 70
|
||||
|
||||
[heater_fan my_nozzle_fan]
|
||||
pin: ar7
|
||||
|
||||
[fan]
|
||||
pin: ar9
|
||||
|
||||
[mcu]
|
||||
serial: /dev/ttyUSB0
|
||||
pin_map: arduino
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 1000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[display]
|
||||
lcd_type: uc1701
|
||||
cs_pin: ar25
|
||||
a0_pin: ar27
|
||||
encoder_pins: ^!ar31, ^!ar33
|
||||
click_pin: ^!ar35
|
||||
kill_pin: ar64
|
||||
|
||||
[bltouch]
|
||||
sensor_pin: ar18
|
||||
control_pin: ar11
|
||||
x_offset: 0
|
||||
y_offset: 18
|
||||
z_offset: 1.64
|
||||
|
||||
# The homing_override section modifies the default G28 behavior
|
||||
[homing_override]
|
||||
set_position_z: 0
|
||||
axes: z
|
||||
gcode:
|
||||
G90
|
||||
G1 Z5 F600
|
||||
G28 X0 Y0
|
||||
G1 X118 Y118 F3600
|
||||
G28 Z0
|
||||
|
||||
# Mesh Bed Leveling.
|
||||
[bed_mesh]
|
||||
samples: 3
|
||||
sample_retract_dist: 5
|
||||
min_point: 5,0
|
||||
max_point: 230,210
|
||||
probe_count: 9,9
|
|
@ -27,6 +27,7 @@ CONFIG ../../config/printer-lulzbot-taz6-2017.cfg
|
|||
CONFIG ../../config/printer-makergear-m2-2012.cfg
|
||||
CONFIG ../../config/printer-micromake-d1-2016.cfg
|
||||
CONFIG ../../config/printer-seemecnc-rostock-max-v2-2015.cfg
|
||||
CONFIG ../../config/printer-tevo-flash-2018.cfg
|
||||
CONFIG ../../config/printer-velleman-k8200-2013.cfg
|
||||
CONFIG ../../config/printer-wanhao-duplicator-i3-plus-2017.cfg
|
||||
CONFIG ../../config/printer-wanhao-duplicator-6-2016.cfg
|
||||
|
|
Loading…
Reference in New Issue