3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
klipper/lib/README

30 lines
1.2 KiB
Plaintext
Raw Normal View History

avr: Initial support for Atmel AT90USB1286 mcu Add GPIO definitions for the AT90USB1286. Add code for communicating over USB port on AT90USB1286. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2016-06-05 02:34:39 +03:00
This directory contains external library code.
The pjrc_usb_serial directory contains code from:
http://www.pjrc.com/teensy/usb_serial.html
lib: Add Atmel SAM3x8e ARM CMSIS files Add the ARM CMSIS definitions (obtained from an Arduino copy of libsam) in preparation for Arduino Due support. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2016-06-14 21:25:42 +03:00
version 1.7 (extracted on 20160605). It has been modified to compile
sched: Introduce sched_wake_tasks() function to wake up tasks Add function to indicate when tasks need to be run. This will allow the scheduler code to know if there are any tasks that need to be processed. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-08-07 18:33:31 +03:00
on recent versions of gcc, to support asynchronous notification of
incoming data, and to not use SOF interrupts. See usb_serial.patch for
the modifications.
lib: Add Atmel SAM3x8e ARM CMSIS files Add the ARM CMSIS definitions (obtained from an Arduino copy of libsam) in preparation for Arduino Due support. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2016-06-14 21:25:42 +03:00
The cmsis-sam3x8e directory contains code from the Arduino project:
https://www.arduino.cc/
pru: Add initial pru_rpmsg library code for Beaglebone PRU Add external code for using RPMsg on the Beaglebone PRU. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-05-08 04:19:10 +03:00
version 1.5.1 (extracted on 20160608). It has been modified to compile
with gcc's LTO feature. See cmsis-sam3x8e.patch for the modifications.
hub-ctrl: Add support for micro-controller reset via RPi usb power toggling Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-13 19:09:37 +03:00
Add STM32F103 port Add a fully functional STM32F1 port, currently mostly targeting STM32F103 microcontrollers. This requires an 8 MHz XTAL. The maximum possible step rate is around 282K steps per second. This uses stm32flash to burn the firmware. The bootloader needs to be started by setting BOOT0 to 1 and resetting the MCU. There is no automatic bootloader, unlike on Arduino. Signed-off-by: Grigori Goronzy <greg@kinoho.net>
2018-03-31 16:34:59 +03:00
The cmsis-stm32f1 and the hal-stm32f1 directories contain code from
STMicroelectronics:
http://www.st.com/en/embedded-software/stm32cubef1.html
version 1.6.0 (extracted 20180330).
hub-ctrl: Add support for micro-controller reset via RPi usb power toggling Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-13 19:09:37 +03:00
The hub-ctrl directory contains code from:
https://github.com/codazoda/hub-ctrl.c/
revision 42095e522859059e8a5f4ec05c1e3def01a870a9.
pru: Add initial pru_rpmsg library code for Beaglebone PRU Add external code for using RPMsg on the Beaglebone PRU. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-05-08 04:19:10 +03:00
The pru_rpmsg directory contains code from:
https://github.com/dinuxbg/pru-gcc-examples
revision 425a42d82006cf0aa24be27b483d2f6a41607489. The code is taken
from the repo's hc-sr04-range-sensor directory. It has been modified
so that the IEP definitions compile correctly. See pru_rpmsg.patch for
the modifications.