176 lines
3.1 KiB
INI
176 lines
3.1 KiB
INI
|
# This file contains common pin mappings for the BIGTREETECH Manta M4P
|
||
|
|
# To use this config, the firmware should be compiled for the
|
||
|
|
# STM32G0B1 with a "8KiB bootloader" and USB communication.
|
||
|
|
|
||
|
|
# See docs/Config_Reference.md for a description of parameters.
|
||
|
|
|
||
|
|
[stepper_x]
|
||
|
|
step_pin: PC6
|
||
|
|
dir_pin: PA14
|
||
|
|
enable_pin: !PC7
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 40
|
||
|
|
endstop_pin: ^PC0
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 235
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_y]
|
||
|
|
step_pin: PB10
|
||
|
|
dir_pin: !PB2
|
||
|
|
enable_pin: !PB11
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 40
|
||
|
|
endstop_pin: ^PC1
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 235
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_z]
|
||
|
|
step_pin: PB0
|
||
|
|
dir_pin: !PC5
|
||
|
|
enable_pin: !PB1
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 8
|
||
|
|
endstop_pin: ^PC2
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 270
|
||
|
|
|
||
|
|
[extruder]
|
||
|
|
step_pin: PB3
|
||
|
|
dir_pin: PB4
|
||
|
|
enable_pin: !PD5
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 33.500
|
||
|
|
nozzle_diameter: 0.400
|
||
|
|
filament_diameter: 1.750
|
||
|
|
heater_pin: PC8
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: PA0
|
||
|
|
control: pid
|
||
|
|
pid_Kp: 22.2
|
||
|
|
pid_Ki: 1.08
|
||
|
|
pid_Kd: 114
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 250
|
||
|
|
|
||
|
|
#[filament_switch_sensor filament_sensor]
|
||
|
|
#switch_pin: ^!PC15
|
||
|
|
|
||
|
|
[heater_bed]
|
||
|
|
heater_pin: PD8
|
||
|
|
sensor_type: Generic 3950
|
||
|
|
sensor_pin: PC4
|
||
|
|
control: watermark
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 130
|
||
|
|
|
||
|
|
[fan]
|
||
|
|
pin: PD2
|
||
|
|
|
||
|
|
#[heater_fan fan1]
|
||
|
|
#pin: PD3
|
||
|
|
|
||
|
|
#[heater_fan fan2]
|
||
|
|
#pin: PD4
|
||
|
|
|
||
|
|
#[heater_fan SoC_fan]
|
||
|
|
#pin: CB1: gpio79
|
||
|
|
#pin: RPI: gpio26
|
||
|
|
|
||
|
|
[mcu]
|
||
|
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
||
|
|
|
||
|
|
[printer]
|
||
|
|
kinematics: cartesian
|
||
|
|
max_velocity: 180
|
||
|
|
max_accel: 3000
|
||
|
|
max_z_velocity: 5
|
||
|
|
max_z_accel: 100
|
||
|
|
|
||
|
|
########################################
|
||
|
|
# EXP1 / EXP2 (display) pins
|
||
|
|
########################################
|
||
|
|
|
||
|
|
[board_pins]
|
||
|
|
aliases:
|
||
|
|
# EXP1 header
|
||
|
|
EXP1_1=PD6, EXP1_3=PB9, EXP1_5=PA15, EXP1_7=PA9, EXP1_9=<GND>,
|
||
|
|
EXP1_2=PB8, EXP1_4=PC3, EXP1_6=PA10, EXP1_8=PB5, EXP1_10=<5V>,
|
||
|
|
# EXP2 header
|
||
|
|
EXP2_1=PB14, EXP2_3=PC11, EXP2_5=PC12, EXP2_7=PC13, EXP2_9=<GND>,
|
||
|
|
EXP2_2=PB13, EXP2_4=PA8, EXP2_6=PB15, EXP2_8=<RST>, EXP2_10=<NC>
|
||
|
|
|
||
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
||
|
|
|
||
|
|
########################################
|
||
|
|
# TMC2209 configuration
|
||
|
|
########################################
|
||
|
|
|
||
|
|
#[tmc2209 stepper_x]
|
||
|
|
#uart_pin: PB12
|
||
|
|
#run_current: 0.800
|
||
|
|
#diag_pin:
|
||
|
|
|
||
|
|
#[tmc2209 stepper_y]
|
||
|
|
#uart_pin: PC10
|
||
|
|
#run_current: 0.800
|
||
|
|
#diag_pin:
|
||
|
|
|
||
|
|
#[tmc2209 stepper_z]
|
||
|
|
#uart_pin: PC9
|
||
|
|
#run_current: 0.800
|
||
|
|
#diag_pin:
|
||
|
|
|
||
|
|
#[tmc2209 extruder]
|
||
|
|
#uart_pin: PA13
|
||
|
|
#run_current: 0.600
|
||
|
|
#diag_pin:
|
||
|
|
|
||
|
|
########################################
|
||
|
|
# TMC5160 configuration
|
||
|
|
########################################
|
||
|
|
|
||
|
|
#[[tmc2130 stepper_x]
|
||
|
|
#cs_pin: PB12
|
||
|
|
#spi_bus: spi1
|
||
|
|
#diag1_pin: PG6
|
||
|
|
#run_current: 0.800
|
||
|
|
#stealthchop_threshold: 999999
|
||
|
|
|
||
|
|
#[tmc2130 stepper_y]
|
||
|
|
#cs_pin: PC10
|
||
|
|
#spi_bus: spi1
|
||
|
|
#diag1_pin: PG9
|
||
|
|
#run_current: 0.800
|
||
|
|
#stealthchop_threshold: 999999
|
||
|
|
|
||
|
|
#[tmc2130 stepper_z]
|
||
|
|
#cs_pin: PC9
|
||
|
|
#spi_bus: spi1
|
||
|
|
#diag1_pin: PG10
|
||
|
|
#run_current: 0.650
|
||
|
|
#stealthchop_threshold: 999999
|
||
|
|
|
||
|
|
#[tmc2130 extruder]
|
||
|
|
#cs_pin: PA13
|
||
|
|
#spi_bus: spi1
|
||
|
|
#diag1_pin: PC15
|
||
|
|
#run_current: 0.650
|
||
|
|
#stealthchop_threshold: 999999
|
||
|
|
|
||
|
|
#[bltouch]
|
||
|
|
#sensor_pin: PC14
|
||
|
|
#control_pin: PA1
|
||
|
|
|
||
|
|
#[adxl345]
|
||
|
|
#cs_pin: PD9
|
||
|
|
#spi_bus: spi1
|
||
|
|
#axes_map: z,y,-x
|
||
|
|
|
||
|
|
#[neopixel rgb1]
|
||
|
|
#pin: PD0
|
||
|
|
|
||
|
|
#[neopixel rgb2]
|
||
|
|
#pin: PD1
|