77 lines
1.4 KiB
INI
77 lines
1.4 KiB
INI
|
# This file contains pin mappings for the Wanhao Duplicator i3 mini.
|
||
|
|
# (circa 2017) To use this config, the firmware should be compiled
|
||
|
|
# for the AVR atmega2560.
|
||
|
|
# Pin numbers and other parameters were extracted from the official
|
||
|
|
# Marlin source available at: https://github.com/garychen99/i3Mini
|
||
|
|
|
||
|
|
# See the example.cfg file for a description of available parameters.
|
||
|
|
|
||
|
|
[stepper_x]
|
||
|
|
step_pin: ar22
|
||
|
|
dir_pin: !ar23
|
||
|
|
enable_pin: !ar57
|
||
|
|
step_distance: 0.0125
|
||
|
|
endstop_pin: ^!ar19
|
||
|
|
position_endstop: 120
|
||
|
|
position_max: 120
|
||
|
|
homing_speed: 30.0
|
||
|
|
|
||
|
|
[stepper_y]
|
||
|
|
step_pin: ar25
|
||
|
|
dir_pin: ar26
|
||
|
|
enable_pin: !ar24
|
||
|
|
step_distance: 0.0125
|
||
|
|
endstop_pin: ^!ar18
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 135
|
||
|
|
homing_speed: 30.0
|
||
|
|
|
||
|
|
[stepper_z]
|
||
|
|
step_pin: ar29
|
||
|
|
dir_pin: ar39
|
||
|
|
enable_pin: !ar28
|
||
|
|
step_distance: 0.0025
|
||
|
|
endstop_pin: ^!ar38
|
||
|
|
position_endstop: 0.5
|
||
|
|
position_max: 100
|
||
|
|
|
||
|
|
[extruder]
|
||
|
|
step_pin: ar55
|
||
|
|
dir_pin: !ar56
|
||
|
|
enable_pin: !ar54
|
||
|
|
step_distance: 0.010638298
|
||
|
|
nozzle_diameter: 0.400
|
||
|
|
filament_diameter: 1.750
|
||
|
|
heater_pin: ar4
|
||
|
|
sensor_type: NTC 100K MGB18-104F39050L32
|
||
|
|
sensor_pin: analog13
|
||
|
|
control: pid
|
||
|
|
pid_Kp: 22.2
|
||
|
|
pid_Ki: 1.08
|
||
|
|
pid_Kd: 114
|
||
|
|
min_temp: 1
|
||
|
|
max_temp: 265
|
||
|
|
|
||
|
|
[fan]
|
||
|
|
pin: ar12
|
||
|
|
|
||
|
|
[mcu]
|
||
|
|
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
||
|
|
pin_map: arduino
|
||
|
|
|
||
|
|
[printer]
|
||
|
|
kinematics: cartesian
|
||
|
|
max_velocity: 300
|
||
|
|
max_accel: 3000
|
||
|
|
max_z_velocity: 5
|
||
|
|
max_z_accel: 100
|
||
|
|
|
||
|
|
[display]
|
||
|
|
lcd_type: uc1701
|
||
|
|
cs_pin: ar41
|
||
|
|
a0_pin: ar40
|
||
|
|
rst_pin: ar27
|
||
|
|
click_pin: ^!ar5
|
||
|
|
encoder_pins: ^ar3, ^ar2
|
||
|
|
kill_pin: ar64
|