2018-01-13 07:59:57 +03:00
|
|
|
# This file contains pin mappings for the 2017 Creality CR-10S. To use
|
|
|
|
|
# this config, the firmware should be compiled for the AVR atmega2560.
|
|
|
|
|
|
|
|
|
|
# See the example.cfg file for a description of available parameters.
|
|
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: ar54
|
|
|
|
|
dir_pin: ar55
|
|
|
|
|
enable_pin: !ar38
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^ar3
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 300
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: ar60
|
|
|
|
|
dir_pin: ar61
|
|
|
|
|
enable_pin: !ar56
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^ar14
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 300
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: ar46
|
|
|
|
|
dir_pin: !ar48
|
|
|
|
|
enable_pin: !ar62
|
|
|
|
|
step_distance: .0025
|
|
|
|
|
endstop_pin: ^ar18
|
|
|
|
|
position_endstop: 0.5
|
2018-05-16 01:53:40 +03:00
|
|
|
position_max: 400
|
2018-01-13 07:59:57 +03:00
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: ar26
|
|
|
|
|
dir_pin: ar28
|
|
|
|
|
enable_pin: !ar24
|
|
|
|
|
step_distance: .010526
|
|
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: ar10
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: analog13
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 22.2
|
|
|
|
|
pid_Ki: 1.08
|
|
|
|
|
pid_Kd: 114
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 250
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: ar8
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: analog14
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 690.34
|
|
|
|
|
pid_Ki: 111.47
|
|
|
|
|
pid_Kd: 1068.83
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 130
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: ar9
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/ttyUSB0
|
|
|
|
|
pin_map: arduino
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 300
|
|
|
|
|
max_accel: 3000
|
|
|
|
|
max_z_velocity: 5
|
|
|
|
|
max_z_accel: 100
|
2018-04-08 18:14:48 +03:00
|
|
|
|
|
|
|
|
[display]
|
|
|
|
|
lcd_type: st7920
|
|
|
|
|
cs_pin: ar16
|
|
|
|
|
sclk_pin: ar23
|
|
|
|
|
sid_pin: ar17
|
2018-10-21 02:27:53 +03:00
|
|
|
encoder_pins: ^ar33, ^ar31
|
|
|
|
|
click_pin: ^!ar35
|
