90 lines
1.6 KiB
INI
90 lines
1.6 KiB
INI
|
# Test config for sdcard_loop
|
||
|
|
[virtual_sdcard]
|
||
|
|
path: test/klippy/sdcard_loop
|
||
|
|
|
||
|
|
[display_status]
|
||
|
|
|
||
|
|
# Override to support unlimited belt size
|
||
|
|
# (homing Z simply resets its virtual position to 0.0)
|
||
|
|
[homing_override]
|
||
|
|
axes: xyz
|
||
|
|
set_position_x: 0
|
||
|
|
set_position_y: 0
|
||
|
|
set_position_z: 0
|
||
|
|
gcode:
|
||
|
|
G92 X0 Y0 Z0
|
||
|
|
|
||
|
|
|
||
|
|
[stepper_x]
|
||
|
|
step_pin: ar54
|
||
|
|
dir_pin: ar55
|
||
|
|
enable_pin: !ar38
|
||
|
|
step_distance: .0125
|
||
|
|
endstop_pin: ^ar3
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 200
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_y]
|
||
|
|
step_pin: ar60
|
||
|
|
dir_pin: !ar61
|
||
|
|
enable_pin: !ar56
|
||
|
|
step_distance: .0125
|
||
|
|
endstop_pin: ^ar14
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 200
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_z]
|
||
|
|
step_pin: ar46
|
||
|
|
dir_pin: ar48
|
||
|
|
enable_pin: !ar62
|
||
|
|
step_distance: .0025
|
||
|
|
endstop_pin: ^ar18
|
||
|
|
position_endstop: 0.5
|
||
|
|
position_max: 200000000
|
||
|
|
|
||
|
|
[extruder]
|
||
|
|
step_pin: ar26
|
||
|
|
dir_pin: ar28
|
||
|
|
enable_pin: !ar24
|
||
|
|
step_distance: .004242
|
||
|
|
nozzle_diameter: 0.500
|
||
|
|
filament_diameter: 3.500
|
||
|
|
heater_pin: ar10
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: analog13
|
||
|
|
control: pid
|
||
|
|
pid_Kp: 22.2
|
||
|
|
pid_Ki: 1.08
|
||
|
|
pid_Kd: 114
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 210
|
||
|
|
|
||
|
|
[heater_bed]
|
||
|
|
heater_pin: ar8
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: analog14
|
||
|
|
control: watermark
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 110
|
||
|
|
|
||
|
|
[mcu]
|
||
|
|
serial: /dev/ttyACM0
|
||
|
|
pin_map: arduino
|
||
|
|
|
||
|
|
[printer]
|
||
|
|
kinematics: cartesian
|
||
|
|
max_velocity: 300
|
||
|
|
max_accel: 3000
|
||
|
|
max_z_velocity: 5
|
||
|
|
max_z_accel: 100
|
||
|
|
|
||
|
|
[sdcard_loop]
|
||
|
|
|
||
|
|
[gcode_macro M808]
|
||
|
|
gcode:
|
||
|
|
{% if params.K is not defined and params.L is defined %}SDCARD_LOOP_BEGIN COUNT={params.L|int}{% endif %}
|
||
|
|
{% if params.K is not defined and params.L is not defined %}SDCARD_LOOP_END{% endif %}
|
||
|
|
{% if params.K is defined and params.L is not defined %}SDCARD_LOOP_DESIST{% endif %}
|