150 lines
2.8 KiB
INI
150 lines
2.8 KiB
INI
|
# This file contains pin mappings for the Robo3D R2 ROBOmainboard 2.1.5.
|
||
|
|
# To use this config, the firmware should be compiled for the AVR atmega2560.
|
||
|
|
#
|
||
|
|
# See docs/Config_Reference.md for a description of parameters.
|
||
|
|
#
|
||
|
|
# The filament runout sensor is gpio21 on the RPi host. Host MCU setup is
|
||
|
|
# documented in docs/RPi_microcontroller.md.
|
||
|
|
|
||
|
|
[stepper_x]
|
||
|
|
step_pin: PF0
|
||
|
|
dir_pin: PF1
|
||
|
|
enable_pin: !PD7
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 40
|
||
|
|
endstop_pin: ^PE5
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 200
|
||
|
|
homing_speed: 120
|
||
|
|
|
||
|
|
[stepper_y]
|
||
|
|
step_pin: PF6
|
||
|
|
dir_pin: PF7
|
||
|
|
enable_pin: !PF2
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 40
|
||
|
|
endstop_pin: ^PJ1
|
||
|
|
position_endstop: 197
|
||
|
|
position_min: 0
|
||
|
|
position_max: 200
|
||
|
|
homing_speed: 120
|
||
|
|
|
||
|
|
[stepper_z]
|
||
|
|
step_pin: PL3
|
||
|
|
dir_pin: PL1
|
||
|
|
enable_pin: !PK0
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 4
|
||
|
|
# Required if not using probe for the virtual endstop
|
||
|
|
# endstop_pin: ^PD3
|
||
|
|
# position_endstop: 250 # Will need ajustment
|
||
|
|
endstop_pin: probe:z_virtual_endstop
|
||
|
|
homing_speed: 10.0
|
||
|
|
position_max: 250
|
||
|
|
position_min: -10
|
||
|
|
|
||
|
|
[extruder]
|
||
|
|
step_pin: PA4
|
||
|
|
dir_pin: PA6
|
||
|
|
enable_pin: !PA2
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 21
|
||
|
|
nozzle_diameter: 0.400
|
||
|
|
filament_diameter: 1.750
|
||
|
|
heater_pin: PB4
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: PK5
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 290
|
||
|
|
control: pid
|
||
|
|
pid_kp: 27.740
|
||
|
|
pid_ki: 1.581
|
||
|
|
pid_kd: 121.707
|
||
|
|
|
||
|
|
# Not enabled in stock R2 config or supported by Robo3D
|
||
|
|
#[extruder1]
|
||
|
|
#step_pin: PC1
|
||
|
|
#dir_pin: PC3
|
||
|
|
#enable_pin: !PC7
|
||
|
|
#heater_pin: PH6
|
||
|
|
#sensor_type: EPCOS 100K B57560G104F
|
||
|
|
#sensor_pin: PK7
|
||
|
|
|
||
|
|
[probe]
|
||
|
|
pin: ^PD2
|
||
|
|
x_offset: 2
|
||
|
|
y_offset: 30
|
||
|
|
z_offset: 10 # Safe value. Adjust for your nozzle offset.
|
||
|
|
sample_retract_dist: 1.0
|
||
|
|
# Below are very conservative settings, as the IR probe has repeatability
|
||
|
|
# issues depending on visual characteristics of the build surface.
|
||
|
|
samples: 3
|
||
|
|
samples_tolerance: 0.2
|
||
|
|
samples_tolerance_retries: 5
|
||
|
|
samples_result: median
|
||
|
|
|
||
|
|
[safe_z_home]
|
||
|
|
home_xy_position: 100, 70
|
||
|
|
speed: 150
|
||
|
|
z_hop: 10
|
||
|
|
z_hop_speed: 10
|
||
|
|
|
||
|
|
[bed_mesh]
|
||
|
|
speed: 200
|
||
|
|
horizontal_move_z: 8
|
||
|
|
mesh_min: 30, 30
|
||
|
|
mesh_max: 170, 170
|
||
|
|
probe_count: 4, 4
|
||
|
|
fade_start: 1
|
||
|
|
fade_end: 5
|
||
|
|
|
||
|
|
# Configured in Marlin as sensor 12:
|
||
|
|
# 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
|
||
|
|
# (calibrated for Makibox hot bed)
|
||
|
|
[thermistor NTCS0603E3104FXT]
|
||
|
|
temperature1: 25
|
||
|
|
resistance1: 100000
|
||
|
|
temperature2: 50
|
||
|
|
resistance2: 29536
|
||
|
|
temperature3: 125
|
||
|
|
resistance3: 1908
|
||
|
|
|
||
|
|
[heater_bed]
|
||
|
|
heater_pin: PH5
|
||
|
|
sensor_type: NTCS0603E3104FXT
|
||
|
|
sensor_pin: PK6
|
||
|
|
control: pid
|
||
|
|
pid_kp: 72.263
|
||
|
|
pid_ki: 1.606
|
||
|
|
pid_kd: 812.963
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 125
|
||
|
|
|
||
|
|
[fan]
|
||
|
|
pin: PH4
|
||
|
|
|
||
|
|
[controller_fan board]
|
||
|
|
pin: PE3
|
||
|
|
|
||
|
|
[output_pin caselight]
|
||
|
|
pin: PH3
|
||
|
|
pwm: False
|
||
|
|
value: 1
|
||
|
|
|
||
|
|
[mcu]
|
||
|
|
serial: /dev/ttyACM0
|
||
|
|
|
||
|
|
# Uncomment the below if the host MCU is configured.
|
||
|
|
#[mcu host]
|
||
|
|
#serial: /tmp/klipper_host_mcu
|
||
|
|
#
|
||
|
|
# [filament_switch_sensor sensor0]
|
||
|
|
# switch_pin: host:gpio21
|
||
|
|
|
||
|
|
[printer]
|
||
|
|
kinematics: cartesian
|
||
|
|
max_velocity: 300
|
||
|
|
max_accel: 3000
|
||
|
|
max_z_velocity: 20
|
||
|
|
max_z_accel: 1000
|