2020-06-25 19:43:52 +03:00
|
|
|
# This file contains pin mappings for the Creality Ender 5 Plus.
|
|
|
|
|
# Ender 5 Plus stock uses a Creality v2.2 board, similar to CR-20 Pro.
|
|
|
|
|
# To use this config, the firmware should be compiled for the AVR
|
|
|
|
|
# atmega2560.
|
|
|
|
|
|
2020-11-17 02:47:32 +03:00
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
2020-06-25 19:43:52 +03:00
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: PF0
|
|
|
|
|
dir_pin: PF1
|
|
|
|
|
enable_pin: !PD7
|
2020-12-14 17:09:19 +03:00
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 40
|
2020-06-25 19:43:52 +03:00
|
|
|
endstop_pin: ^PE5
|
|
|
|
|
position_endstop: 350
|
|
|
|
|
position_max: 350
|
|
|
|
|
homing_speed: 100
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: PF6
|
|
|
|
|
dir_pin: PF7
|
|
|
|
|
enable_pin: !PF2
|
2020-12-14 17:09:19 +03:00
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 40
|
2020-06-25 19:43:52 +03:00
|
|
|
endstop_pin: ^PJ1
|
|
|
|
|
position_endstop: 350
|
|
|
|
|
position_max: 350
|
|
|
|
|
homing_speed: 100
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: PL3
|
|
|
|
|
dir_pin: PL1
|
|
|
|
|
enable_pin: !PK0
|
2020-12-14 17:09:19 +03:00
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 4
|
2020-06-25 19:43:52 +03:00
|
|
|
endstop_pin: probe:z_virtual_endstop
|
|
|
|
|
position_max: 400
|
|
|
|
|
position_min: 0
|
|
|
|
|
homing_speed: 10.0
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: PA4
|
|
|
|
|
dir_pin: PA6
|
|
|
|
|
enable_pin: !PA2
|
2020-12-14 17:09:19 +03:00
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 33.683
|
2020-06-25 19:43:52 +03:00
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: PB4
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PK5
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 22.2
|
|
|
|
|
pid_Ki: 1.08
|
|
|
|
|
pid_Kd: 114
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 260
|
|
|
|
|
|
|
|
|
|
[safe_z_home]
|
|
|
|
|
home_xy_position: 180, 180
|
|
|
|
|
speed: 100
|
|
|
|
|
z_hop: 10
|
|
|
|
|
z_hop_speed: 5
|
|
|
|
|
|
|
|
|
|
[bltouch]
|
|
|
|
|
sensor_pin: ^PD3
|
|
|
|
|
control_pin: PB5
|
|
|
|
|
x_offset: -45
|
|
|
|
|
y_offset: 0
|
|
|
|
|
z_offset: 0
|
|
|
|
|
speed: 3.0
|
|
|
|
|
pin_up_touch_mode_reports_triggered: False
|
|
|
|
|
|
|
|
|
|
[bed_mesh]
|
|
|
|
|
speed: 100
|
|
|
|
|
horizontal_move_z: 8
|
|
|
|
|
mesh_min: 50, 50
|
2022-01-10 05:13:53 +03:00
|
|
|
mesh_max: 300, 300
|
|
|
|
|
probe_count: 3, 3
|
2020-06-25 19:43:52 +03:00
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: PH5
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PK6
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 690.34
|
|
|
|
|
pid_Ki: 111.47
|
|
|
|
|
pid_Kd: 1068.83
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 130
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: PH6
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_AK06VNAB-if00-port0
|
|
|
|
|
|
2021-03-15 05:04:45 +03:00
|
|
|
[filament_switch_sensor filament_sensor]
|
|
|
|
|
switch_pin:PE4
|
|
|
|
|
|
2020-06-25 19:43:52 +03:00
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 300
|
|
|
|
|
max_accel: 2500
|
|
|
|
|
max_z_velocity: 5
|
|
|
|
|
max_z_accel: 100
|
