2019-02-08 23:00:23 +03:00
|
|
|
# This file contains common pin mappings for the Azteeg X5 Mini v3. To use
|
2019-06-20 18:23:30 +03:00
|
|
|
# this config, the firmware should be compiled for the LPC1769.
|
2019-02-08 23:00:23 +03:00
|
|
|
|
2020-11-17 02:47:32 +03:00
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
2019-02-08 23:00:23 +03:00
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: P2.1
|
|
|
|
|
dir_pin: P0.11
|
|
|
|
|
enable_pin: !P0.10
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^P1.24
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 200
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: P2.2
|
|
|
|
|
dir_pin: P0.20
|
|
|
|
|
enable_pin: !P0.19
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^P1.26
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 200
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: P2.3
|
|
|
|
|
dir_pin: P0.22
|
|
|
|
|
enable_pin: !P0.21
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^P1.28
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 200
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: P2.0
|
|
|
|
|
dir_pin: P0.5
|
|
|
|
|
enable_pin: !P0.4
|
|
|
|
|
step_distance: .002
|
|
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: P2.5
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: P0.24
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 22.2
|
|
|
|
|
pid_Ki: 1.08
|
|
|
|
|
pid_Kd: 114
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 250
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: P2.7
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: P0.23
|
|
|
|
|
control: watermark
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 130
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: P0.26
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 300
|
|
|
|
|
max_accel: 3000
|
|
|
|
|
max_z_velocity: 5
|
|
|
|
|
max_z_accel: 100
|
|
|
|
|
|
|
|
|
|
[mcp4451 stepper_digipot1]
|
|
|
|
|
i2c_address: 44
|
|
|
|
|
# Scale the config so that wiper values can be specified in amps.
|
|
|
|
|
scale: 2
|
|
|
|
|
# wiper 0 is X (aka alpha), 1 is Y, 2 is Z, 3 is E0
|
|
|
|
|
wiper_0: 1.0
|
|
|
|
|
wiper_1: 1.0
|
|
|
|
|
wiper_2: 1.0
|
|
|
|
|
wiper_3: 1.0
|
|
|
|
|
|
|
|
|
|
# Mini Viki2 LCD - this board does not work with Reprap LCDs
|
|
|
|
|
#[display]
|
|
|
|
|
#lcd_type: uc1701
|
|
|
|
|
#cs_pin: P0.16
|
|
|
|
|
#a0_pin: P2.6
|
|
|
|
|
#encoder_pins: ^!P3.25, ^P3.26
|
|
|
|
|
#click_pin: ^!P2.11
|
