2020-04-30 03:45:19 +03:00
|
|
|
# This file contains common pin mappings for Tronxy P802M printer. To
|
|
|
|
|
# use this config, the firmware should be compiled for the AVR
|
|
|
|
|
# atmega1284p. The Tronxy P802MA is similar, but will need
|
|
|
|
|
# auto leveling configuration.
|
|
|
|
|
|
|
|
|
|
# Note that the "make flash" command does not work with Tronxy boards -
|
|
|
|
|
# the boards are typically flashed with this command:
|
|
|
|
|
# avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex
|
|
|
|
|
|
2020-11-17 02:47:32 +03:00
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
2020-04-30 03:45:19 +03:00
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: PD7
|
|
|
|
|
dir_pin: PC5
|
|
|
|
|
enable_pin: !PD6
|
2020-12-14 17:09:19 +03:00
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 32
|
2020-04-30 03:45:19 +03:00
|
|
|
endstop_pin: ^!PC2
|
|
|
|
|
position_endstop: -8
|
|
|
|
|
position_max: 220
|
|
|
|
|
position_min: -45
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: PC6
|
|
|
|
|
dir_pin: PC7
|
|
|
|
|
enable_pin: !PD6
|
2020-12-14 17:09:19 +03:00
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 32
|
2020-04-30 03:45:19 +03:00
|
|
|
endstop_pin: ^!PC3
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_min: -5
|
|
|
|
|
position_max: 220
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: PB3
|
|
|
|
|
dir_pin: !PB2
|
|
|
|
|
enable_pin: !PA5
|
2020-12-14 17:09:19 +03:00
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 8
|
2020-04-30 03:45:19 +03:00
|
|
|
endstop_pin: ^!PC4
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 230
|
|
|
|
|
homing_speed: 20
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: PB1
|
|
|
|
|
dir_pin: PB0
|
|
|
|
|
enable_pin: !PD6
|
2020-12-14 17:09:19 +03:00
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 33.600
|
2020-04-30 03:45:19 +03:00
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: PD5
|
|
|
|
|
sensor_type: ATC Semitec 104GT-2
|
|
|
|
|
sensor_pin: PA7
|
|
|
|
|
control: pid
|
|
|
|
|
pid_kp: 23.060
|
|
|
|
|
pid_ki: 1.025
|
|
|
|
|
pid_kd: 129.711
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 250
|
|
|
|
|
max_extrude_only_distance: 400
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: PD4
|
|
|
|
|
sensor_type: ATC Semitec 104GT-2
|
|
|
|
|
sensor_pin: PA6
|
|
|
|
|
control: pid
|
|
|
|
|
pid_kp: 72.174
|
|
|
|
|
pid_ki: 1.677
|
|
|
|
|
pid_kd: 776.767
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 110
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: PB4
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_A96PLN7R-if00-port0
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 300
|
|
|
|
|
max_accel: 1000
|
|
|
|
|
max_z_velocity: 20
|
|
|
|
|
max_z_accel: 100
|
|
|
|
|
|
|
|
|
|
[display]
|
|
|
|
|
lcd_type: hd44780
|
|
|
|
|
rs_pin: PA3
|
|
|
|
|
e_pin: PA2
|
|
|
|
|
d4_pin: PD2
|
|
|
|
|
d5_pin: PD3
|
|
|
|
|
d6_pin: PC0
|
|
|
|
|
d7_pin: PC1
|
|
|
|
|
up_pin: PA1
|
|
|
|
|
analog_range_up_pin: 9000, 13000
|
|
|
|
|
down_pin: PA1
|
|
|
|
|
analog_range_down_pin: 800, 1300
|
|
|
|
|
click_pin: PA1
|
|
|
|
|
analog_range_click_pin: 2000, 2500
|
|
|
|
|
back_pin: PA1
|
|
|
|
|
analog_range_back_pin: 4500, 5000
|
|
|
|
|
#kill_pin: PA1
|
|
|
|
|
#analog_range_kill_pin: 400, 600
|
