2020-12-21 18:49:38 +03:00
|
|
|
# This file contains pin mappings for the stock 2020 Creality Ender 6.
|
|
|
|
|
# To use this config, during "make menuconfig" select the
|
|
|
|
|
# STM32F103 with a "28KiB bootloader" and with "Use USB for
|
|
|
|
|
# communication" disabled.
|
|
|
|
|
|
|
|
|
|
# Because this printer has factory wiring, mounts, and firmware for
|
|
|
|
|
# a BLTouch, but does not ship with one at this time, default values
|
|
|
|
|
# for the sensor have been specified, but disabled, in anticipation of
|
|
|
|
|
# future revisions or user modification. User should take care to
|
|
|
|
|
# customize the offsets, particularly z-offset, for their specific unit.
|
|
|
|
|
|
|
|
|
|
# If you prefer a direct serial connection, in "make menuconfig"
|
|
|
|
|
# select "Enable extra low-level configuration options" and select the
|
|
|
|
|
# USART3 serial port, which is broken out on the 10 pin IDC cable used
|
|
|
|
|
# for the LCD module as follows:
|
|
|
|
|
# 3: Tx, 4: Rx, 9: GND, 10: VCC
|
|
|
|
|
|
|
|
|
|
# Flash this firmware by copying "out/klipper.bin" to a SD card and
|
|
|
|
|
# turning on the printer with the card inserted. The firmware
|
|
|
|
|
# filename must end in ".bin" and must not match the last filename
|
|
|
|
|
# that was flashed.
|
|
|
|
|
|
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: PB8
|
|
|
|
|
dir_pin: PB7
|
|
|
|
|
enable_pin: !PC3
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 40
|
|
|
|
|
endstop_pin: ^PA5
|
|
|
|
|
position_endstop: 260
|
|
|
|
|
position_max: 260
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: PC2
|
|
|
|
|
dir_pin: !PB9
|
|
|
|
|
enable_pin: !PC3
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 40
|
|
|
|
|
endstop_pin: ^PA6
|
|
|
|
|
position_endstop: 260
|
|
|
|
|
position_max: 260
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: PB6
|
|
|
|
|
dir_pin: PB5
|
|
|
|
|
enable_pin: !PC3
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 8
|
|
|
|
|
position_endstop: 0.0 # disable to use BLTouch
|
|
|
|
|
endstop_pin: ^PA7 # disable to use BLTouch
|
|
|
|
|
# endstop_pin: probe:z_virtual_endstop # enable to use BLTouch
|
|
|
|
|
# position_min: -5 # enable to use BLTouch
|
|
|
|
|
position_max: 400
|
|
|
|
|
|
|
|
|
|
# [safe_z_home] # enable for BLTouch
|
|
|
|
|
# home_xy_position: 150.7, 137
|
|
|
|
|
# speed: 100
|
|
|
|
|
# z_hop: 10
|
|
|
|
|
# z_hop_speed: 5
|
|
|
|
|
|
|
|
|
|
# [bltouch] # enable for BLTouch
|
|
|
|
|
# sensor_pin: ^PB1
|
|
|
|
|
# control_pin: PB0
|
2021-02-19 03:28:43 +03:00
|
|
|
# x_offset: -20.7
|
|
|
|
|
# y_offset: -7
|
2020-12-21 18:49:38 +03:00
|
|
|
# z_offset: 2.4
|
|
|
|
|
# speed: 3.0
|
|
|
|
|
|
|
|
|
|
# [bed_mesh] # enable for BLTouch
|
|
|
|
|
# speed: 100
|
|
|
|
|
# mesh_min: 10, 10
|
2021-02-19 03:28:43 +03:00
|
|
|
# mesh_max: 239, 239
|
2020-12-21 18:49:38 +03:00
|
|
|
# algorithm: bicubic
|
|
|
|
|
# probe_count: 5,5
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
max_extrude_only_distance: 1000.0
|
|
|
|
|
step_pin: PB4
|
|
|
|
|
dir_pin: !PB3
|
|
|
|
|
enable_pin: !PC3
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 22.857
|
|
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: PA1
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PC5
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 26.949
|
|
|
|
|
pid_Ki: 1.497
|
|
|
|
|
pid_Kd: 121.269
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 260
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: PA2
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PC4
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 327.11
|
|
|
|
|
pid_Ki: 19.20
|
|
|
|
|
pid_Kd: 1393.45
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 100
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: PA0
|
|
|
|
|
|
|
|
|
|
[filament_switch_sensor e0_sensor]
|
|
|
|
|
switch_pin: PA4
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
|
|
|
|
restart_method: command
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: corexy
|
|
|
|
|
max_velocity: 500
|
|
|
|
|
max_accel: 2000
|
|
|
|
|
max_z_velocity: 10
|
|
|
|
|
max_z_accel: 100
|
